Make Your Own Low-Budget Light Bulb Changers

Make changing light bulbs easier and safer by building your very own low-budget light bulb changers.

| November/December 1983

  • Short Light Bulb Changer
    This short version of the light bulb changer can help you change bulbs in your house and garage without the dangers of getting on a shaky chair or stepladder.
  • Long Light Bulb Changer
    This longer light bulb changer makes it easier to change light bulbs in high reach areas without ever having to leave the ground.
  • Light Bulb Changer Diagram
    This diagram gives an accurate representation of the parts and pieces of your light bulb changer should look when put together and finished.

  • Short Light Bulb Changer
  • Long Light Bulb Changer
  • Light Bulb Changer Diagram

As the days grow shorter, it's a sure bet that folks will be relying more upon household lighting to extend their productive hours. However, as convenient as light bulbs are, they do burn out . . . and replacing them — especially those set in a hard-to-reach locations — can be a troublesome (and sometimes even dangerous) chore.

So, to make shaky stepladders and teetering chairs a thing of the past, our research staffers devised the two incandescent light bulb changers on a low-budget. The first will handle conventional indoor globes typical of those you might find in hallway ceilings, garages, and attics. It's little more than a 3' (more or less) length of 3/4" CPVC pipe forced into the neck of a half-liter plastic soda pop bottle. Since the outside diameter o f the pipe is about 7/8" (and thus is slightly larger than the opening in the bottle), one end of the plastic staff must be sanded to a taper so the joining parts are compatible. The bulb basket can then be formed by cutting of the container's base (be sure to leave about 3/8" of contour around the edge so the tool can grip the bulb), and stuffing the inside of the bottle with wads of foam upholstery padding.

Using the tool is just a matter of popping the basket over the expired bulb and pulling gently on the handle while turning it to unscrew the lamp from its socket. After the old globe is discarded, a new one can be pressed into the basket and threaded into place.

The second changer was designed for use on indoor and outdoor spotlights. Because those bulbs have somewhat flat faces, you can employ a suction cup, rather than a basket, to grip the glass. To make this "grabber", first locate a 3" diameter rubber "foot" from a car top carrier (it must have a 1/4" socket — not a stem — for mounting, and should be available as a replacement part in auto accessory stores), and then run a 1/4" drill bit in the cup's socket and through its core to penetrate the "sucker".

Now, find yourself about 15 feet of 1/4" plastic tubing and a straight nylon connector to fit that hose, and scrounge up an 8' length of 3/4" Schedule 40 PVC pipe to serve as a handle . Depending on the design of your suction cup, it'll either fit snugly inside the pipe or force you to make two perpendicular cuts across the pipe's diameter and jam the four "fingers" over the cup's mount to hold it securely.

In any case, before you fasten the suction tip in place, install the connector to the end of the hose and then press it into the socket in back of the cup. With this done, you can feed the free end of the hose through the length of PVC pipe and let it extend out the open end.

Mother Earth News Fair Schedule 2019


Next: April, 27-28 2019
Asheville, NC

Whether you want to learn how to grow and raise your own food, build your own root cellar, or create a green dream home, come out and learn everything you need to know — and then some!


Subscribe Today - Pay Now & Save 64% Off the Cover Price

Money-Saving Tips in Every Issue!

Mother Earth NewsAt MOTHER EARTH NEWS, we are dedicated to conserving our planet's natural resources while helping you conserve your financial resources. You'll find tips for slashing heating bills, growing fresh, natural produce at home, and more. That's why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.95 (USA only).

You may also use the Bill Me option and pay $17.95 for 6 issues.

Canadian Subscribers - Click Here
International Subscribers - Click Here
Canadian subscriptions: 1 year (includes postage & GST).

Facebook Pinterest Instagram YouTube Twitter flipboard

Free Product Information Classifieds Newsletters