Making Paper at Home

Making paper yourself is a bit time-consuming but not especially complicated, and you probably have most or all of the necessary raw materials.
By Marrianne Saddington
December/January 1993
Add to My MSN

A mold and deckle are essential equipment if you're making paper yourself. The mold is a durable wood frame, one side of which is covered by a fine-gauge, porous material.
ILLUSTRATION: MARRIANNE SADDINGTON
Slideshow


Content Tools

Related Content

Build Your Own Yurt Using Papercrete

Papercrete – concrete made with paper – recycles household trash into a durable material that's perf...

Chic Crafts From Upcycled Clothing and Homemade Recycled Paper

You can upcycle (make crafts from recycled materials) to beautifuly and simplify your world! Have a ...

The Responsibility of the Corporate World to the Environment

For decades, corporations have been able to skirt past being held accountable for any environmental ...

Flatulence to Fuel in Brooklyn

A new wastewater treatment plant in Greenpoint, Brooklyn, will use methane gas to produce energy.

Although making paper is a common enough activity, making paper at home is not because few are familiar with the techniques involved. As a calligrapher, I was initially drawn to making my own paper so that I would be able to practice my art on interesting and unusual "canvas."

I'd never realized how simple the process actually is. You probably have most of the equipment already; what you don't have you can make. Also, in addition to creating beautiful stationery, I take pride in knowing that I'm helping to reduce waste in our throwaway society.

Waste Paper into Pulp 

Recycled-paper pulp can be made from tissues, computer paper, photocopier paper, wrapping paper, brown paper, note paper, or envelopes — all used on their own or in combination. Tear the paper into pieces measuring approximately one inch square and soak in water overnight. The better the quality of the paper, the smaller you need to tear the pieces and the longer you need to soak them. For example, tissues can be torn into quite large pieces and soaked for only 30 minutes, while watercolor paper needs to be torn into pieces less than one inch square and soaked for two or three days. If you're in a hurry, pour boiling water over the torn paper and allow it to stand for an hour or two.

Place a small handful of wet, torn paper and two cups of water in a blender and blend for 15 to 30 seconds. (Thick cardboard or quality papers will take longer.) After a while, experience will tell you how long to blend different kinds of paper. Remember when first starting out, blend paper for the shortest possible time — just long enough for the fibers to separate. Stop the machine after 15 seconds and check; if there are still large pieces of paper visible, allow another 10 seconds and check again. If the pulp is too thick, add more water; do not dilute it too much or you will produce fine, fragile sheets that are difficult to work with. Don't worry about little bits that do not break down entirely; they will add character to your finished product.

If you don't have a blender, beat the soaked paper strips into pulp by pounding them in a bucket with a thick stick or bottle filled with water. Although pounding the pulp is historically more authentic than using electric appliances, be forewarned: it is hard, time-consuming work.

After blending the pulp, pour it into a bucket or large plastic bottle until you have enough for several sheets. Figure that one load in the blender will make one thin sheet of 8 1/2" x 11" paper. A two-gallon bucket of pulp will make 20 to 25 sheets.

From Pulp to Paper 

Pour three quarts of pulp into a vat (a square plastic dishpan with a capacity of about five gallons of water) and add cold water up to three inches from the top. Then stir the pulp gently with your hand or a wooden spoon. (Do this before forming each sheet to prevent the pulp from settling on the bottom.) Dampen the mesh on your mold (see "Build a Mold & Deckle" at the end of this article) before forming your first sheet.

Facing the vat, hold the mold with both hands by the short sides and lower vertically into the far side of the vat. Then tilt the mold gently towards you until it is lying horizontally, about two inches below the surface of the water. Be careful not to bump the sides of the vat with the mold, which can cause ridges.

Next, hold the deckle against the mold with your thumbs on top and fingers underneath as you immerse both frames in the vat. As they clear the surface — but before the water drains away — lift them out of the vat. Give the mold and deckle a gentle shake backwards, forwards, and sideways to disperse the fibers. Be sure to move from your shoulders, not just the wrist). Then drain the wet sheet for about 30 seconds before removing the deckle gently. Do not to let any drops fall on the wet sheet — they will leave water marks.

At this point, you have two drying options. The first and easier method is to simply tilt the frame on its side and leave it outside to dry. On a windy or sunny day, the paper will dry within a couple of hours. In sunny weather, and with two molds in operation, it's possible to make up to 112 sheets a day using this method. Be careful of strong winds, however, which can topple the mold and ruin your paper. To prevent this, lean the mold against a flower pot in a sunny location, using a brick or heavy stone placed at the base of it to hold it firm. Another potential disaster is rain, which can create gaping holes. And don't leave your paper outside overnight when small creatures may get to it.

To remove the paper from the mold, slide a sharp knife under a corner of the paper and work it along the top edge in order to loosen it. Then gently peel off the paper. To press, leave paper in a heavy book for a week.

Method 2: The Couching Technique 

Your other option is to "couch" (or lay down) the paper onto wet felt (felt is available at fabric stores). First, create a small pile of five to six wet pieces of felt to form a soft pad. (Without this pad, your paper may form badly.) A wet folded towel or wet piece of carpet pad may also be placed underneath the pad of felts in order to create even more of a cushion.

Next, rest the mold with the long left-hand side of the frame against the right-hand side of the felt, pulp facing left. Hold the mold vertically (your left hand should be holding the raised left side of the frame). Using both hands and a gentle rocking motion, lower the mold (pulp against the felt) down flat on the felt with your left hand, and lift it up with the right. While the motion should be smooth, the pressure should be sufficient enough to transfer the wet pulp onto the felt. Press the mold firmly if this is your first time; with practice you'll be able to do this in one smooth movement. If your first sheet isn't successful, just place another wet felt onto the first sheet of paper and couch a second sheet onto this.

Continue this process until you have a substantial pile of felts and paper. After you've created a pile of 10 or so sheets of paper, feel free to remove the towel or carpet. Then keep piling the felts until you have anywhere between 20 and 50 of them. Now it's time to press.

The simplest way to press a pile of felts is to sandwich them between two boards and stand on the pile for 10 minutes. Then, for even further pressing, stack bricks or a bucket of water on the board and let sit for a few hours. When you return, take out your pile and place on a flat surface. Peel away the top felt in order to reveal the first wet sheet of paper. Separate each felt (with its wet sheet) from the one below. Peel them apart carefully, gently lifting a corner without lifting the sheet below. Go slow.

Then hang your couched paper indoors on a drying rack or clothesline with clothespins to dry. Once dry, remove the paper from the felt by sliding a sharp knife under a corner of the paper and working the knife along the top edge to loosen. Turn the felt over so the paper is face down (on a clean, dry surface) and gently peel the felt away. Press the paper in a heavy book for one week.

Storing Extra Pulp

Newly made or leftover pulp can be stored in sealed bottles or buckets for up to a few weeks. Pour pulp through a drainage bag, stocking, or colander lined with mesh, rinse well under running water, and return it back to its container slightly diluted. Experience will tell you which consistency works best, but a general rule of thumb is to dilute one cup of wet, drained pulp with one to two cups of water. If the pulp is still too thick, dilute it even more so that your sheets won't end up lumpy.

If after a week or so your pulp starts to smell badly, add one teaspoon of household bleach for each two quarts of pulp. Before using the pulp again, however, make sure that you give it a good, thorough rinsing.

For longer storage, some recommend draining and then freezing excess pulp. Others (myself included) suggest draining the excess pulp through mesh and then storing it in the refrigerator in a sealed plastic bag. For indefinite storage, drain pulp through a stocking and hang to dry. When you need some, simply break off pieces, soak them in water for an hour, and blend again.


Build a Mold and Deckle

The mold is nothing more than a simple, durable wood frame. To make one, nail or glue at the corners two pieces of 13"-long wood (the sides) with two 8 1/2"-long pieces of wood (the top and bottom). Strips of wood should measure 1" x 2" in thickness, and the inside area of the frame should be 8 1/2" x 11". You can further reinforce the corners with brass L-shaped braces.

Cover the frame with mesh stretched as taut as possible and then pin or nail to the frame. Materials that can be used as mesh include: net curtaining, fiberglass window screening, plastic cross-stitch fabric, silk-screen mesh, or any porous fabric with a fine gauge. If using fabric, wet it before stretching so that it won't sag when placed in water.

The deckle is a removable, open frame that rests on top of the mesh and contains the pulp within the surface area of the screen. It is the same size as the mold and determines the size of the sheet of paper to be formed. If a deckle is not used, the paper formed will be thinner and the edge more irregular. For a simple but perfectly adequate deckle, make a second frame identical to the mold, but only one inch deep. Omit the mesh.


Editor's Note: Reprinted with permission fromby Marianne Saddington. Copyright © New Holland Ltd. Published by Storey Communications.

Previous | 1 | 2 | 3 | 4 | Next






Post a comment below.

 

Priya
9/6/2013 4:56:56 AM
Your information about paper recycling is useful. Using papers for making the paper cup is one of the recycling activities of papers.

Anitha
8/27/2013 6:57:45 AM
This article is useful for children to know how to make papers. Different varieties of papers used to make cup are made with high quality raw materials which enables recycling. http://www.reeldiecuttingmachine.com/paper-cup-machine.php

Elm Whitewillow
6/25/2012 10:13:15 PM
I agree with Jeff. Also the instructions were a bit confusing.

JEFFREY TERHOEVE
10/24/2011 8:19:29 AM
Nice story. It would be nice to see some pictures of the actual process and some of what the finished product would/could look like.

William Pople
7/24/2011 6:06:15 AM
I would think you could check the acidity of your slurry with a pool tester and add alter the ph as needed. There are places on the net to see the correct chemicals to use. It becomes a big math problem to determine what and how much to use. If you have a small vat and only a little way to go to reduce the acidity then you can use a small quantity of a strong base or a large quantity of a weak base. Example of common bases are agricultural lime and backing soda; both common and Eco-friendly. Depending on how far off the ph is use the drain and fill method to dilute the acid and bring the ph up to Neutral(neutral is 7.0 acid is less Alkaline/base is higher). Note adding bleach to the water will make the slurry slightly acidic. I'm not sure if neutralizing the bleach will negate the mold killing/ whitening effect one would be using it for. One thing I'm curious about is if we wanted to add seeds to the paper to make it "plant-able"; when do we sprinkle the seeds? I know to add flowers or herbs to the paper you would do it while draining the paper to have a few strands on top to encapsulate the decorations. Would the seeds go in then or right before the couching?

Ruth Bradfield
2/9/2011 3:08:45 PM
Good information on paper making. However if you use recycled papers that are not acid free, your paper will not be archival, and it will yellow and become brittle, and ruin any other thing you may put on it, like photos. There is an aerosol spray available that says it makes paper acid free, but it will be expensive to spray a lot of paper with this. Recycling SOUNDS good, but if you want to create a work of art that will last you might want to think twice about using recycled papers with an unknown acid quantity. Newspaper is notoriously bad to use for paper making as it is highly acidic. Just look at what happens to a newspaper after it sits around for a while and you will see what the problem is. Maybe the author has a way to make his recycled paper acid-free. If so he should include that information in this article. Cardboard also has a lot of unknown glues and stuff in it.








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.