Build a Portable DC Arc Welder for $20

If you can scrounge an old lawn mower, an automobile alternator, and a 12-volt battery, you can build your own portable DC arc welder.
By the MOTHER EARTH NEWS editors
November/December 1980
Add to My MSN

The completed portable DC arc welder looked like this.
PHOTO: MOTHER EARTH NEWS STAFF
Slideshow


Content Tools

Related Content

Climbing Sequoias for Climate Change

For almost two decades, the Archangel Ancient Tree Archive group has done what the experts said was ...

EPA to Tighten Standards on Lawn Equipment

New EPA regulations require 35 percent reduced emissions from lawn-care equipment by 2011.

R-House: An Efficient, Affordable Urban Housing Prototype

An affordable prototype home helps revitalize a blighted Syracuse, New York, neighborhood--and could...

Lawn Mower Tuneup

Take time to tune up your gas-powered push mower so that it runs as efficiently as possible. Here ar...

Given a choice between adding either arc or gas welding to the workshop, most tinkerers find a small AC arc unit to be an inexpensive and impressively versatile piece of equipment. However, for those occasional remote outdoor chores that come up around most farmsteads, gas is just about the only practical choice. (Of course, there are portable electric welders available, and one could use a shop unit and tote along a generator ... but either approach represents a considerable investment, especially if the devices will be used only to accomplish infrequent in-the-field repairs.)

As it happens, MOTHER EARTH NEWS' researchers run into a fair number of remote welding jobs out at our Eco-Village property — from tacking together a windplant frame to sealing a hydroplant pipe — that are just plain inaccessible to the Lincoln automatic feed unit that they prefer. Therefore, it didn't take long for one member of our team to get so fed up with the hassle of loading both a generator and an arc welder into a pickup truck that he began combining some odds and ends around the shop to make his own portable DC arc welder.

Experimenter Dennis Burkholder decided that — after scrounging up an old power mower, a set-aside Delco-Remy automobile alternator, and a weary but serviceable 12-volt deep-cycle battery — he had just about everything he needed to build a portable, intermittent-duty, low-voltage, welder. Sure enough, after trying a couple of different combinations of the scrap components, he came up with what must be the least expensive (and strangest looking) arc welder ever assembled.

Essentially, the welder is powered by the roughly 50 amps that the Delco-Remy alternator is capable of producing . . . and is adjusted by varying the speed of the lawnmower engine. But the 12-volt battery is needed to balance out those surges that occur when the arc is struck or broken. Furthermore, Dennis found that the setup worked a lot more smoothly with two 1 1/2-ohm, 8-amp resistors placed in series with the field of the alternator, to cut the field voltage to about 6 volts. (In fact, without the two resistors, striking an arc would nearly kill the 3-HP Briggs & Stratton engine!)

Considering that the parts for the project are almost all scavenged, the welder is amazingly versatile. For one thing, DC capability is often preferred for smooth sheet-metal work, and our lawnmower unit can have its polarity reversed for changing the penetration and spatter qualities of its arc! There are, however, a few limitations to the tool's capabilities. First, the maximum heat of the arc is about 50 amps, so the device won't penetrate more than about 1/4" into steel. In addition, it's best not to use the welder for more than about 20 minutes at a time to avoid overheating the alternator (a thermal overload switch tells you when enough is enough).

And finally, the unit's low-voltage DC current presents both an advantage and a disadvantage over conventional AC power. Because the voltage of a circuit determines the distance a spark will jump, the rod used with our portable welder must be held steadily close to the surface of the work to maintain an arc. But, because it is a direct-current welder, there's little tendency for the rod to become stuck.

Of course, the most astounding thing about Dennis's welder is how little it cost. The only components that our researcher was forced to buy were the resistors, which he located at the nearest auto parts store. And — even if your storehouse of valuable discards doesn't equal our — you should still be able to purchase the resistors, wires, switches, pulleys, and V-belt for less than $20. When you think about it, a $20 DC arc welder, with a built-in dolly, might be the workshop bargain of the year!


Previous | 1 | 2 | Next






Post a comment below.

 

gaclements
7/7/2013 10:37:21 AM

That's all it is to make one 


Kenneth P. Wise
7/2/2009 6:43:11 PM
I like all how to's barn building,log homes,solar power.








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.