How to Make an Inexpensive Cold Frame

If you want to extend your gardening season, consider building this effective cold frame greenhouse.
March/April 1982
Add to My MSN


Content Tools

Related Content

What’s the Best Way to Start Seeds Indoors?

Learn how to start seeds indoors using inexpensive fluorescent lights.

Starting Seeds For Spring

By starting seeds indoors, you get a jump start on spring garden planting.

Use Your Cold Frame All Year

Suggestions for getting the most use of your cold frame all year long.

Make Seed Pots From Recycled Newspapers

Homemade transplant pots from newspaper save money and reduce waste.

It's the time of year again when most dedicated gardeners give some thought to getting a jump ahead of the still-chilly weather by utilizing a cold frame to protect delicate seedlings from the effects of spring frosts. Here is one of the least expensive surrogate greenhouses of its size that the staff of MOTHER EARTH NEWS has ever found.

The ideal cold frame, of course, admits sunlight to the plants it contains, to supply them with both the heat and the light they need to prosper and "harden" before being exposed to the real world. At the same time, the cold frame should provide the seedlings with adequate protection from bitter winds and chilling cold.

Cold Frame Building Materials

This particular model requires little more than 1-inch polystyrene insulation board (at 15¢ per square foot), some scrap lath and molding, a 36-inch length of 3/4-inch dowel, assorted hardware, foil tape, and a section of fiberglass-reinforced plastic glazing measuring just over 2-by-4 feet (The last component, at $1.06 per square foot, costs more than the sum of all the other parts . . . but if you enjoy making your own solar collectors, you might well have some leftover FRP around. If not, old storm windows or the glass from them — or even heavy-duty clear plastic — can be used as a suitable, and much less expensive, substitute.)

How to Build a Cold Frame

To build the cold frame, just cut the various pieces to the sizes called for in our drawing, then form the holes that retain the night cover's 10 support dowels. These openings should be about 19 inches apart and 10 inches above the frame walls' lower edge, and can most easily be made by gently heating a short length of 1/2-inch copper pipe (using a torch and a pair of pliers) and then letting this hot tool serve as a "drill" to cut the perforations. It's important not to apply too much heat to the boring wand, though, or the holes will be oversized and the dowels won't fit snugly. (Caution: Do not breathe the fumes given off in this process, since they contain noxious gases.)

Next, assemble the frame by joining all four corners, inside and outside, with aluminum tape . . . then press the 3/4-inch by 24-inch dowel through the two center holes to make the spine that connects the front and back walls, and push the remaining pegs into the rest of the openings in such a way that their "back" ends protrude past the inner surface to form shelves at strategic points around the frame. Keep the spine in place by fastening body washers, scavenged milk jug lids, plexiglass disks, or what have you to its exposed ends, using No. 6 by 3/4-inch flat-head wood screws. Then complete the frame by attaching the two handles to the night cover, again employing scrounged disks as stops.

The light-admitting lid is merely a framework, constructed from 1-by-2s, which holds the glazing in place beneath lath strips tacked to its upper surface. To make it, first miter (at 45 degrees) the ends of each of its side and end rails, then cut a 3/8-inch-wide by 1-inch-deep rabbet into the lower inside edge of the boards, and fashion a 1/4-inch by 1-inch dado — centered — in the upper surfaces of the two longest rails.

Fasten the casing together with three No. 3 by 1/2-inch oval-head wood screws at each corner, then tack the 1/4-inch by 7/8-inch by 25-1/4-inch cross brace to the dadoed rails. Finish up the job by laying the plastic glazing over the framework and driving in brads or finishing nails — through the lath strip molding skirt — to secure it.

Because the polystyrene is apt to deteriorate after long exposure to direct sunlight, it's best to protect it — and the wooden parts of the cold frame — with acrylic latex exterior house paint . . . which won't adversely affect the insulation board.

To put your budget hothouse to use, just sink it about half a foot into the earth, or merely set it on top of some turned-up soil . . . making sure its sloped lid is facing in a more or less southerly direction. (If you choose not to bury the frame, secure it against gusty winds by driving a pair of stakes into the ground and fastening them to the ends of the spine with screws.)

In order to provide for sometimes necessary ventilation, you can either remove the lid completely (on sunny days), or just prop it open (by placing some 2-by-4 scraps at the corners) when the weather is overcast, and hold it in place with a restraining cord tied over it and behind the spine stops. Naturally, the night cover should be installed for the evening and left in place until the sun rises the next day. Furthermore, on especially cold nights — or if you should want to use your cold frame as a "hotbox" — you can always put a few strips of electric heat tape (the kind used to keep household plumbing from freezing) several inches beneath the soil, or just set up a light bulb within the container.

So why not spend a (very) few bucks and beat Jack Frost by three or four weeks? You'll be glad you did when your harvest gets to the dinner table that much sooner!

Previous | 1 | 2 | Next

Post a comment below.


Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.