Build a Homemade Camping Trailer

Homesteaders eager to travel but low on funds can build a homemade camping trailer, includes information on a frame camper, a detailed diagram and instructions.
By Robert Pentecost
July/August 1982
Add to My MSN

Rather than shell out hard-earned cash for motel lodging on family jaunts, I figured I'd put a few bucks, and a bit of effort, into building a homemade camping trailer.
ILLUSTRATION: MOTHER EARTH NEWS STAFF


Content Tools

Related Content

Photo of the Day: Trailer Garden

Photo of the Day blog features a different photo from readers each day. Submit your own photos for a...

Green Builder Gives Airstream Eco-Friendly Makeover

Green builder Jim Gooley gutted an Airstream Trailer and renovated it with cork flooring, clay plast...

Build an Artistic, Recycled and Inexpensive Wooden Desk

Follow this Intructables contributor's step-by-step guide to building a desk with old crates and box...

How Do I Build an Inexpensive Cold Smoker?

Instructions for building a cold smoker (and three other things you can do with steel oil drums).

If you've got travel in your blood but only a little cash in your pocket, build a homemade camping trailer. 

I've been a fan of the great outdoors since my youth, but once I became a family man, I had to think about changing the manner in which I visited the wilds. You see, though all of the Pentecost clan enjoys camping, we don't all appreciate middle-of-the-night close encounters with wild critters . . . and needless to say, the prices of recreational trailers have gone far beyond the reach of many folks, including us.

I didn't, however, let a mere lack of funds prevent our traveling around and experiencing the thrill of new and distant places. Rather than shell out hard-earned cash for motel lodging on family jaunts, I figured I'd put a few bucks, and a bit of effort, into building a homemade camping trailer . . . and still have some money left over to spend on a trip. The result of my brainstorm is the "appropriate technology (or APT) camper" pictured here . . . a lightweight, four-berth tent trailer—built from both new and used components—which cost me less than $350!

BUILDING A CAMPING TRAILER: START AT THE BEGINNING

The heart of my APT Camper is a small, 750-pound-capacity fishing-boat trailer . . . which I picked up, in good condition, for $100. These tag-alongs are typically just under 4 feet wide at the rear and taper inward toward the front. To ready it for camper carrying, I simply welded two Lshaped pieces of 4 inch-broad lightweight channel iron to the trailer's nose, thus providing a 4-foot-wide structural base at the front of the tapered frame. Since the chassis wasn't quite 4 feet wide at the rear, I also had to weld some 1/8 inch by 2 inch by 2 inch by 3 inch angle iron brackets to its side rails in that area to support my trailer's 3/4 inch by 4 foot by 8 foot plywood floor.

After I'd drilled through the brackets and frame members and bored mounting holes in the wooden platform, I started work on the camper's walls. To make them, I first trimmed five 2 by 4's to 8-foot lengths, then cut four 41 inch-long sections. Seventeen 2 by 4's—measuring 15-3/4 inch each—served as vertical studs.

Then, using 1/4 inch by 3 inch lag screws, I fastened 13 of the studs to their respective top and bottom plates, forming three 19 inch-tall wall frames . . . which I went on to fasten to the front and side edges of the plywood floor with bolts run through the bottom plates, the wooden platform, and the trailer frame (or the angle iron brackets) beneath. To enclose the camper's tail end, I framed out two 12 inch-long walls at the rear corners, bolted them to the base as I had the others, and then fastened them to the side walls with lag screws. More screws, placed through the corner studs at the front, helped to make the entire "box" secure.

I covered the wall frames with 1/4 inch exterior-grade plywood, which I fastened to the studs and plates with No. 6 by 1 inch wood screws. And finally, I made a 19 inch-tall, 24 inch-wide door of 2 by 2's covered with the ply wood skin and attached the portal to the walls in the usual manner, with hinges on one side and a standard lock set on the other.

WING IT

In order to provide the camper with bunk space and a protective lid, I attached two "wings"—made from 4 foot by 8 foot sheets of 1/2 inch plywood—to the top of each long wall with Thinges. One of the wooden sheets was left full size, but the other was cut down to 44 inch wide to allow it to clear a 2 by 4 spacer I used to mount the first wing. (This spacer—which I fastened to one wall's top plate—raises the full section of plywood enough to let the narrower sheet fold flat beneath it.)

Then, to stiffen the sleeping platforms, I glued and screwed three evenly spaced 2 by 4 ribs across the breadth of each wing, one near each end and another in the middle, using No. 6 by 1 inch flathead wood screws countersunk into the plywood's surface.

The wooden wings—when extended—are further held in place by a total of six 3/4 inch E.M.T. support poles (three per side) fastened between the ends of the ribs and the trailer frame. After cutting the rods to about 45 inch in length, I flattened one end of each section, drilled a 1/4 inch hole through the metal at that point, and locked a 1/4 inch by 4 inch machine screw into each opening. Then I bored six 1/4 inch holes—each in line with one rib—through the side of the trailer's chassis, and tightened 1/4 inch by 2 inch bolts into the openings, threaded ends out, using double nuts. After bending the bolts upward slightly, I slipped short pieces of 1/4 inch neoprene hose over the studs to assure a snug fit.

With the support poles on their respective studs, I temporarily shored up the plywood wings so they were level, positioned the bolts on the ends of the supports against the ribs, and drilled horizontal 1/4 inch holes through the 2 by 4's at the points I'd marked. By slipping the support bars' bolts through the crosswise bores, I could be sure that each wing was firmly secured.

At this point I had a "winged" camper . . . that would still tip sideways if someone were to sit on one edge. So, to solve that problem, I cut two 28 inch lengths of 1 inch E.M.T. and two 30 inch pieces of 3/4 inch electrical conduit . . . and drilled a 1/4 inch hole through the side of each 1 inch section, about an inch from the end. By securing 3/4 inch pipe hanger clamps to the drilled E.M.T. so that the threaded collars were in line with the bores, I could slide the smaller-diameter tubes inside the larger ones and hold each one fast by a bolt (bent at a right angle) tightened through the clamp to press against the inner conduit section.

To make a foot for each of the telescoping supports, I just purchased a pair of 1 inch E.M.T. to 3/4 inch pipe couplers and two 3/4 inch floor flanges, and fastened them to the bottom of each pole.

Then, to secure the supports at their upper ends (as well as to provide an attaching point for the exterior tent poles), I cut two 8 inch lengths of the channel I'd used to extend the frame and drilled seven 1/4 inch holes through each piece . . . two pairs in line through the part's shoulders—about 4 inch apart and toward one end—and three in a triangular pattern in the base at the opposite end, as shown in the drawing.

By placing the brackets over the ends of the central ribs and drilling through the shoulder holes and the wood between them, I was able to slide some 1/4 inch bolts into the openings to serve as fastening pins. Likewise, 1/4 inch by 2 inch bolts—secured to the brackets' remaining holes in a two-up, one-down arrangement and covered with more fuel line—provided tent pole and support mounts. (The brackets, poles, and other loose hardware can be stored in the bed of the camper when not in use.)

Several coats of exterior paint, applied to all the wooden surfaces (both inside and out), protected the camper's skin and gave it a real quality-built look, too.

FROM CABIN TENT TO CAMPER

I found that actually installing the tent was a simple—and satisfying—task. My 9 foot by 12 foot exterior-frame unit fit the camper just about perfectly, though I had to cut the canvas floor out to allow access to the center bunk area. (I used the scrap to stitch up a snap-in-place weatherproof tarp that protects the trailer when it's towed.)

I merely spread the tent out in place—making sure its door lined up with the camper's entrance—then worked around the perimeter, pulling the canvas walls so they hung over the platform an equal distance all around. By holding the edges temporarily with C-clamps, I was able to set the shelter up and secure an inch or two of folded-over canvas to the underside of the wings, using strips of 1/4 inch plywood ripped to 1 inch widths and held on with 1/2 inch wood screws. Then, to attach the tent to the front and back walls, I simply installed sturdy snap fasteners.

That's about all there was to it, too. Of course, you may want to add some extra "goodies" to your own APT Camper, should you choose to build one (I've included foam mattress pads, an electrical outlet, and a small cabinet in mine), but you can get along quite nicely with the simple setup I've described here. Don't be afraid to improvise, though . . . if you already have a tent, by all means build your camper to suit it, even if it's an odd size. There's nothing like "making do" to save money.

EDITOR'S NOTE: For those who may not feel confident building their own APT Camper just from the descriptions given in this article, the author is offering a construction guide that includes drawings and a materials list. It's available for $10 from Robert Pentecost, Dept. TMEN, Louisville, Kentucky.  

Check your state's motor vehicle regulations concerning registration and insurance of a towed camping trailer before you build. 


Previous | 1 | 2 | 3 | 4 | Next






Post a comment below.

 

bruce coletti_1
2/24/2010 12:57:37 PM
my dad built an almost identical camper as this 30 years ago. And i`ve been trying to find plans for it for years. I could probably build it just from memory, but this is perfect on giving me the minute details a 10 year old wouldn`t have thought about back then. Anyway, i just wanted to say thanx. You would be amazed at how hard it is to find the right item. I typed in do it yourself tent trailer plans and you-all were the only ones that seemed to know what it meant. So thanx again. Everyone elses site was just pop ups, i mean if that is what i`m looking for i would type pop up campers.








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.