Feedback on Sencenbaugh's O2 Delight: Windmill Blade Design

A reader in Romayor, Texas questions the efficiency of the windmill blade design Jim Sencenbaugh used in his O2 Delight windmill. Jim Sencenbaugh explains his decision and comments on current and future refinements he's planning.
By the MOTHER EARTH NEWS editors
July/August 1973
Add to My MSN

Top illustration shows how the lift vector of an airfoil positioned with its curved face to the wind impedes windmill rotation. Bottom illustration shows how the lift vector of an airfoil positioned with it's flat face to the wind aids rotation.

Content Tools

Related Content

Earth Gauge Tip of the Week — Lighten Up

Tips on how to conserve energy and save money with compact fluorescent bulbs during shorter daylight...

Earth Gauge Tip of the Week — Under Pressure

Tips on how to increase your car's fuel efficiency by checking the tire pressure.

Renewable Energy: What's the First Step?

Start cutting your electricity use today, and it will save you a bundle of cash on a renewable energ...

Farm Is Using an Old Method to Reduce the Cost of a Wind Turbine

One farm is able to combine cost savings, with energy sustainability by using a Savonius rotor.

I think that the blades an the Sencenbaugh 02 Powered Delight are mounted with the curvature of the airfoil in the wrong direction. My illustrations are intended to demonstrate that if the blades are mounted as shown in the article, the lift vector of the airfoil—which is perpendicular to a chord drawn between the leading edge and the trailing edge—will have a component opposite to the direction of rotation. The purpose of the fan is to extract energy from the wind by turning its movement into rotational motion of a shaft. Since rotation is what you're after, it seems counterproductive to have the lift of the airfoil pulling against that very action.

If blades are mounted with the curved side away from the wind (that is, the wind coming from the top of the page in my sketches), the lift vector has a component working in the direction of rotation. I wish I could explain that a little less pedantically and a little more poetically, but I said it as clearly as I could. Take a look at some store-bought wind chargers and windmills and see if I'm not right.

author unknown
Romayor, Tex.

The drawing in MOTHER EARTH NEWS is a correct and accurate representation of how the blades were originally built. It was my intention initially to attempt to make the blades self-limiting ... hence the configuration as illustrated. The effective pitch angle was set at 15-16 degrees from the chord line, which provided good low-speed response and sufficient rpm for charge.

Since the article was written and the plans drawn, we have been using a new prop made of laminated birch-ply with the airfoil (retaining the "Clark Y") on the conventional side and with a twisted effective pitch (15 at root to 3 degrees at tip) along its length. The performance, naturally, is greatly improved. I've been sending out supplementary plans (at no extra charge to the buyer) along with instructions on how to rewind the existing alternator to obtain charge at lower speed. With the new prop and rewound alternator we are now obtaining charge in winds of 5 to 6 mph as compared to the 8 to 10 mph wind previously required. Therefore, I'm highly recommending these additional improvements to people now building a unit.

Also, the following modifications to the present plans were made:

[1] Each joint in the tower, besides being secured with Resorcinol and the galvanized nails, should have one 1 1/2 X 8-inch flat-headed wood screw added. Be sure to recess and pre-drill before adding the screw. This "mod" will prevent a poor joint (if the Resorcinol wasn't applied correctly) ... and will greatly add to the strength of the tower.
[2] The screen door spring, which holds the main vane in position, should be constructed of small-diameter wire (No. 20 AWG) and 1/2 inch in diameter. The tension should be adjusted just enough to hold the vane in its normal attitude in moderate (15 mph) winds. If a heavy-duty type spring (No. 16 AWG wire) is used, the pilot vane may not operate properly as designed.

It should be noted that the "Delight" was my first attempt at a small-scale plant . . . and it continues to improve. I'm working on a fly-ball type governor that gives a more linear response to change in pitch and rpm than the present governing mechanism. Also on the workbench is a matching device that will allow all three props to feather as one.

In addition to building up our sailwing, we are experimenting with forming props from paper honeycombed in a pressure mold and using a fiberglass-epoxy skin on the outside. We hope to reduce the weight considerably and thereby further improve performance.

I'd like to thank MOTHER EARTH NEWS for running the article. The response has been very good ... and the resulting correspondence with others enjoyable and informative. We're considering the production of a low-priced commercial plant—in the 400- to 700-watt area—in the near future. I'll keep you informed.

Jim Sencenbaugh
Palo Alto, Calif.

Previous | 1 | 2 | Next

Post a comment below.


Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.