SolaRoll Solar Heater

Back in 1980 you could buy a product that would let you build a freeze-resistant passive solar collector for less than half the price of conventional equipment: the SolaRoll solar heater.
By the MOTHER EARTH NEWS editors
May/June 1980
Add to My MSN

TOP: Diagram of the SolaRoll solar heater.  BOTTOM LEFT: The Solar Flare house built by Mike and Andy Andruzak. BOTTOM RIGHT:  SolaRoll mat stapled beneath the floor radiates solar heat.
PHOTOS: BIOENERGY SYSTEMS/MOTHER EARTH NEWS STAFF


Content Tools

Related Content

Have You Ever Built a Solar Water Heater?

You can use the power of the sun to heat water for your home using manufactured solar hot water syst...

Speaking of Clean Energy

Bill Clinton has 10 recommendations for what the U.S. government should be doing to promote cleaner ...

Zero-VOC Me

Environmental journalist Simran Sethi goes through the process of rejuvenating her hardwood floors, ...

How Do I Remove Rigid Insulation From an Old Water Heater So I Can Make a Solar Batch Heater?

Cleaning up an old water heater just requires two simple tools.

Anyone who's tried to build or even simply install his or her own water heating solar collector has probably had the feeling that — though such devices are efficient, do pay back the money invested in them by reducing (or eliminating) utility bills, and can be reliable producers of hot water — there ought to be a better way to get the job done. After all, even if you ignore the initial high cost of commercial metal sun-catchers (starting at around $15 per square foot) . . . the practical matters of fitting, plumbing, sealing, flow balancing, and freeze protecting them are so complex that such tasks are often left to professionals.

But now, thanks to some innovative thinking on the part of the folks at a company called Bio-Energy Systems, Inc., there actually is a better way to buy and build a collector. Rather than using expensive and hard-to-work copper, steel, or aluminum, Bio-Energy has developed an extruded synthetic rubber heat absorber (with water-carrying tubes cast inside) called SolaRoll.

The EPDM compound (ethylene-propylene-dienemonomer)  is molded into a mat that's 4 3/8" wide, contains six 1/5" diameter tubes, and comes in rolls of 600 linear feet. Any length (up to 100 feet) can be snipped off and used for a single pass from a cold water intake to a hot water exhaust. Thus it's possible to build a 50-foot-long collector by laying out 50 feet of the elastomer, incorporating a 180° turn in the material, and returning. And it has all of its plumbing connections in one location!

Installation Ease

The advantages offered by the SolaRoll solar heater are numerous—as you'll soon see—but perhaps the material is most amazing because it's so easy to put to use. While Bio-Energy doesn't offer complete collectors, it sells (through a growing network of dealers) all of the critical components needed to build such a device. SolaRoll distributors do offer installation service, but the company actually encourages individuals to do their own work instead . . . since the material was designed to be incredibly simple for a homeowner to use.

Bio-Energy sells EPDM edge flashing (in three different styles for various collector configurations), special pre-drilled headers (in copper or plastic), Teflon jam sleeves for solderless sealing at pressures of up to 100 PSI, a mastic to glue the rubber parts to the roof, and the heat-absorber matting itself. All the customer needs to supply are pressure-treated 2 X 4's for framing, insulation (1"-thick Thermax is often used), a glazing (which can vary from 0.025" to 0.125" in thickness), and a few standard hand tools.

Because the rubber components are so light, much of the construction can be done on the ground. Then—once the SolaRoll parts are laid out, trimmed, and sealed into their headers—the assembly can be lifted to the roof and glued in place.

Efficient and Inexpensive

Tests conducted by the University of Connecticut's Solar Energy Evaluation Center indicate that a SolaRoll-equipped collector is every bit as effective as the average commercial unit with a peak efficiency rating of 73%. However, to those who will possibly be paying for such devices, the cost per BTU of heat collected is a much more interesting figure... and in the dollar category no metal collector can touch SolaRoll.

Bio-Energy's components average out at just about $6.00 for each square foot of collector (large installations work out to slightly less and smaller ones are proportionately more expensive). Once you've added the lumber, glazing, and insulation, the per-square-foot price of an owner-installed system rises to between $7.00 and $7.50 . . . a price that is from one-half to one-third that of an equivalent metal system. And, when you consider that a metal collector will need a heat exchanger or a drain-down mechanism—accessories which SolaRoll, since the EPDM compound remains flexible even at temperatures well below freezing, doesn't require — the cost difference increases. (However, SolaRoll can't be used for a domestic water supply without the addition of a heat exchanger.)

The Solar Flare house

One of MOTHER EARTH NEWS' staff members recently had the opportunity to visit a house built by Mike and Andy Andruzak . . . who own Solar Flare Company, the Colorado distributor for SolaRoll. All the heat for the 2,220-square-foot home is provided by a 464-square-foot SolaRoll collector on the roof, with the help of a backup wood-fired Hydro Heater that's plumbed into the same water circulation network. And remember, the dwelling is located high in the chilly Colorado Rockies!

What's more, in Mike's house—which has pretty much become a "guinea pig" on which to test his brother Andy's ideas—SolaRoll not only collects but actually distributes the necessary warmth. From a storage tank built of insulated cinder block and lined with 65-mil plastic, hot water (at about 110°F) is pumped out through copper headers and then carried beneath the home's floors by lengths of SolaRoll heat absorber mat (functioning, in this application, as radiators) that are stapled and glued to the underside of the flooring. Andy pointed out how incredibly easy it was to install the radiant-heat SolaRoll and noted that the material for the entire water-circulating system cost less than $1,000.

The Colorado pair have other schemes in mind for SolaRoll. They intend to set the material into some sidewalks in a new ski area being built. The flexible matting will be heated by a waste-oil boiler to keep the walkways clear in any weather. Of course, a fertile imagination can't help devising new schemes for the application of SolaRoll. It promises to provide one of the revolutions in solar technology that we've all been waiting for.


Previous | 1 | 2 | Next






Post a comment below.

 

Ken Wright
9/21/2010 11:15:47 AM
Mr, Anderson's comment answers Mr. Damme's. EPDM synthetic rubber breaks down in chlorinated water in many cases, enough that the rumor is there was a class action lawsuit around 1988 and those selling epdm solar pool heaters were forced to remedy the failed systems. Monsanto came up with Santoprene as a replacement rubber at the time and those brave enough to service what they sold took it on. It failed even faster. I've written extensively on this topic on my blog at www.h2otsun.blogspot.com My product, Powerstrip is just like Solaroll. In fact I'm pretty sure my headers fit their tubing so if you're looking for teflon inserts I can go one better and offer new headers. They are only $10 each delivered and Solaroll tubes press right on with some soap. There are so few Solaroll systems left that I haven't confirmed the tube size and spacing but I'm pretty sure. Get back to me with tube size and spacing and I'll confirm its a fit. As for parts for 30 years old Solaroll systems....I think they were the biggest casualty of the big class action lawsuit that everyone selling epdm in the solar industry today denies ever happened. http://www.h2otsun.com is the modern day non-epdm version of Solaroll Ken Wright President Hot Sun Industries Inc

Jim Van Damme_1
2/13/2010 8:19:22 AM
Whatever happened to this stuff? I've been running a system for 25 years with no maintenance except two drops of oil a year in the pump, and one transistor in my homemade controller.

Bryant H. Anderson
12/21/2009 4:48:55 PM
I am looking for a source to get replacement tubemat for my panels. The old ones deteriorated in the hot sun when a summer was past without water pumping through the tubemat. Bryant

Wayne_30
6/14/2009 1:57:42 PM
I would also like to find some of the teflon inserts. Can anyone help?

LEONARD_7
5/6/2007 4:42:49 AM
DOES ANYONE KNOW WHERE TO FIND THE TEFLON INSERTS TO USE WITH SOLAROLL?








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.