Solar on a Shoestring: Homemade Solar Thermostat

Solar researcher Dennis Burkholder devised a solar control system that blows heat from his solar heater into his house when he needs it and shuts off when he doesn't.
By the MOTHER EARTH NEWS editors
March/April 1980
Add to My MSN

Schematic for the collector thermostat control system. 
MOTHER EARTH NEWS STAFF
Slideshow


Content Tools

Related Content

Do I Really Need a Solar Collector to Heat My Home, or Can I Get Just as Much Heat by Adding a South-Facing Window?

Here are the pros and cons of using south facing windows for home heating, rather than solar collect...

What Is a Solar Hot-Air Collector?

You can use a solar hot-air collector to heat your home with renewable energy. Here’s more about how...

Tulikivi Water-Heating System Unveiled at HPBA Expo

Unit helps homeowners heat more space while slashing high hot water bills

The Gift of Solar Energy

Here are three of the season’s brightest and cleanest gifts for a greener holiday celebration.

The MOTHER EARTH NEWS article "Solar on a Shoestring: Mother's Corrugated Collector" featured an incredibly inexpensive solar collector which could be built from lumberyard materials. Well, that project proved to be so successful that a member of our re search team has put in a few extra hours developing an automatic control system for the "Corrugated Collector" (or most any passive sun-grabber). . . so you can take advantage of 19,000 BTU per hour without lifting a finger.

Mother's Automatic Collector Control

One of MOTHER EARTH NEWS' solar researchers, Dennis Burkholder, was so enthusiastic about the low cost collector we featured in this column that he took a day off recently to build one of the sun-catchers on the side of his own home. And—not surprisingly— Dennis couldn't resist doing a little additional design-as-you-go engineering with the basic corrugated collector concept by adding his own solar control.

First of all, the fearless fabricator decided to cover the whole south-facing side of his house with collectors . . . including the windows. Though the view is now a bit blurry through the rippled fiberglass, neither of the affected bedrooms has suffered any significant loss of natural light. In addition—since he was about to put roughly 200 square feet of "solar furnace" into action—Dennis increased the vent size to 6" x 12" and ran a 10" duct through his attic . . . to drop the warm air into the center of his home. With these modifications, he was able to use a blower with a flow rate of 400 cubic feet per minute.

Well, our researcher did such a good job of reworking the collector that he soon found out his house would overheat during the middle of the day if he didn't shut the "fan" off. So the obvious next step was to set up the solar heater to work on demand. The solution is simple and inexpensive, and you can wire up one of "Dennis's brainstorms" for your own collector in about an hour or so.

The solar control system works by placing one temperature sensor in the living area of the house and another inside the collector, then wiring the two sensors and the blower into a series circuit. Thus there must be both a need for heat and sufficient warmth on hand in the collector before the blower will switch on.

You can start the installation by lifting the upper panel of corrugated fiberglass (if you've already built your corrugated collector) to expose a point about a foot from the top, and two "channels" over from the air intake. Drill a 1/2" hole through the Thermax insulating board and the wall, and run two wires through the opening. Then use screws to fasten a 70-160°F warm air fan control to the collector surface, and attach each of the wires to a pole on the control. The positive wire will go to a power source inside the house, and the neutral wire will connect to one terminal on a 115V thermostat located near the main thermostat for your heating system. (WARNING: Before you make the "hot" connection to your home's electrical system, BE SURE TO SHUT OFF THE CIRCUIT BREAKER FOR THAT SECTION OF YOUR ABODE'S WIRING TO AVOID SHOCK.)

Once the hot-wire/control/thermostat circuit is complete, you can set the temperature scale on the collector's sensor to about 120-130°F and close the corrugated fiberglass again. Next, run a wire from the remaining lug on the interior thermostat to the positive pole on the blower, and then connect the ground post on the fan to any available ground in your house's wiring.

Now you can flip the circuit breaker back on again and set the interior thermostat to a temperature a few degrees higher than your main furnace control. As long as there's heat in the collector, your energy-consuming traditional heating system will be taking a money-saving rest. As a matter of fact, Dennis has found that—on a clear, crisp winter day—the blower will kick in as soon as 20 minutes after sunrise and keep his home warm all day long. And best of all, his heating bills have already dropped from $90 per month to a little under $40!


Previous | 1 | 2 | Next






Post a comment below.

 

Joel Pointon
6/2/2011 11:31:41 AM
Where does one find the "warm air fan control"

Robert Eidt
12/28/2008 6:02:54 PM
Nice and simple, but no mention that the fan control is a "Normally Open (NO)" thermostat. I think it's obvious to most but I thought I might clarify. This means the collector must reach a preset temp before it closes its contact. While in this state, if the thermostat inside the home calls for heat then, while both conditions are met, the blower will run. If either the hose comes to its preset temperature, or the collector temperature drops below it's preset temperature, the blower will turn off. -Thanks!!








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.