You can build a recycled water heater wood stove for $35.00 or less.
Photo By Fotolia/JGima
Learn how this recycled water heater wood stove can heat your home while helping
Build a Recycled Water Heater Wood Stove
(Note: Since this article was published in 1978, building codes and homeowners insurance
rules have changed, and federal rules governing wood stoves have been adopted. This
stove design may not comply with various federal and local regulations. Readers
are advised to check with appropriate officials before installing this stove in
their homes. — MOTHER)
Most homebuilt wood-burning stoves are scabbed together from old 55-gallon drums.
And they more or less do the job they're supposed to do . . . despite the fact that
they're notoriously inefficient users of fuel, are difficult to regulate, rapidly
burn through, and are so ugly that most people will only tolerate them out in the
garage or workshop.
Perhaps the single really good thing that can be said for the majority of the 55-gallon-drum
burners is that (usually) it doesn't cost very much to put one of them together
or at least it didn't used to. Here lately, though, the steel barrels have become
increasingly difficult to find . . . and, when you do locate one of the containers,
it frequently has a seven dollar price tag at fixed to it.
There must be a better way to go about assembling a homemade wood-burning stove.
And there is: As MOTHER was recently shown by Wilton, Iowa's Robert Wars (who, incidentally,
just happens to be the brother of MOTHER researcher Emerson Smyers).
"Forget about messing around with old 55-gallon drums," Bob told us. "What you want
to build your stove out of is a discarded electric water heater tank . . . for at
least four good reasons:
"In the first place, the walls of such a tank are a minimum of three to four times
as thick as the metal in a 55-gallon barrel . . . which means that a water heater
drum will make a much tougher stove that will last a lot longer.
"Second, when you build a firebox from a junked water heater tank, it's very easy
to make the stove as airtight and efficient as any $500 woodburner on the market.
And I can't say that about any 55-gallon-drum stove I've ever seen.
"Third, if you construct your heater the way I tell you to, it'll be easy to load,
it will have excellent fire and temperature control, and it'll look classy enough
to put on display right in the living room.
"And fourth, you can build one of my 'water heater' stoves for even less than most
folks now spend putting together a 55-gallon-barrel wood-burner. As a matter of
fact, I scrounged up everything that went into mine. Which means that the
stove cost me only the labor — one good long day — that I used building
Well, now. Those were pretty big claims. Especially since we were listening to them
while looking at some photographs of a flat-out good looking stove. So,
in our best and most devious "backwoods of North Carolina" fashion, we challenged
ole Bob to prove everything he'd just told us.
And then — just to put him at as large a cost disadvantage as we could —
we spit a couple of times, looked at Smyers out of the corner of our eye, and innocently
said, "Of course you know, Bob, that a lot of our readers have trouble scavenging
up project materials the way you do. So, other than letting you recycle an old water
heater tank, we'll just have to make you buy and pay new prices for everything else
that goes into any stove you build for us."
"Oh, of course!" Bob answered. And it wasn't so much what he said as the way he
said it which told us right then and there that we were the ones who'd been had.
Shucks. This Iowa slicker knew from the beginning that he could build a $500 stove
and never use more'n $35 worth of materials doing it.
The Secret of the Smyers Low-Cost Wood Stove
As Bob Smyers drafted his brother, Emerson, and set about the construction of one
of his now-famous stoves, it was easy to see that the recycled-into-a-firebox electric
water heater tank was the real secret of his recycled water heater wood stove's
low cost. Also its ease of assembly. Heck. Once you've found your "junked but still
in good condition" water heater tank, you've already got about three-quarters of
your stove "custom made" just the way you want it.
And it really isn't difficult to find one of these tanks, either. Most of the landfills
scattered around the country, in fact, are so filled with the containers that we've
developed a sneaking suspicion the old water heaters breed out there. Maybe not
. . . but there sure are a lot of 'em "out there" for the taking.
Any discarded electric (forget the gas ones for this project) water heater from
30- to 50-gallon capacity will convert nicely into a stove. We've come to think,
however, that one of the 30-gallon tanks (with a diameter of 20 inches and a length
of 32 inches) makes the best-looking wood-burner of all.
Pick and choose a little from your friendly local landfills, dumps, or the alleyways
behind appliance stores until you find just the tank or tanks you want. Then (if
you're doing your "shopping" in a landfill or dump) strip off the lightweight sheet
metal "wrapper" and insulation right in the field and make sure that the main tank
inside isn't rusted out or filled with corrosion. Or, if circumstances dictate,
you can do this stripping back home in your shop and then haul the castoff sheet
metal and insulation back to the dump when you're ready to discard them.
Downloadable construction details
Water Heater Stove Diagram 1 and
Water Heater Stove Diagram 2 will help the building process.
The Rest of the Low-Cost Wood Stove is Easy
Anyone with a cutting torch and welder will find the rest easy. And if you don't
own or operate such equipment, scout around until you find a competent welding shop
that'll convert your tank at a reasonable price.
Lay the container on its side and add legs and the "loading hopper box with hinged
lid" as illustrated in the accompanying drawing. Then weld in the "exhaust stack"
or "smoke boot" as shown. Make sure that all seams are airtight and that the hopper
box lid fits snugly (airtight) too. he draft control is, perhaps, the most critical
part of all. If it's well made and doesn't leak, you'll have good and positive control
of your finished stove's blaze and temperature at all times. Conversely, if it isn't
well made and it does leak, you won't. Work carefully and do the job right.
Once the stove is completely assembled, paint all its outside surfaces with Rustoleum
Bar-B-Q black paint or "high temperature engine paint". You've just built yourself
one mighty fine wood-burner! And, even if you bought everything (approximately 65
pounds of steel) except the recycled water heater tank, you shouldn't have spent
more than $35 on the project. (Bob and Emerson built MOTHER's demonstration model
in one short day — six hours — for a total cost of $31.54.)
This Low-Cost Wood Stove Works!
MOTHER researcher Dennis Burkholder has been using our original "water heater wood
stove" to warm his entire 1,100 square-foot house since last fall and he's constantly
amazed at the large amount of heat and small amount of ashes the unit produces.
He's also been pleasantly surprised by the way the heater holds a fire overnight.
"All I do in the morning," says Dennis, "is jar the stove a couple of times, open
the draft a bit . . . and the ole log-burner snaps right to life."