Green Homes

Building for the future, today – combining the best of historical wisdom and modern technology.

Add to My MSN

Insulation Upgrades: How to Handle the Walls

11/16/2011 12:40:52 PM

Tags: energy efficiency, insulation upgrade, wall insulation, Tim Snyder

Using injection foam to insulate walls It’s not unusual for a household to consume twice as much energy as necessary. Of course, there are many “culprits” responsible for this high energy demand: an inefficient water heater, phantom loads from electronic devices, leaky ductwork and an outdated furnace, just for starters. But one of the most common denominators in energy-wasting houses is inadequate insulation – or more specifically, too many air leaks and too little insulation.  

In earlier blogs, I talked about the importance of air-sealing and insulating the attic according to recommendations established by the U.S. Dept. of Energy. If you have access to your attic space through a hatch or drop-down stair, your attic is a good candidate for an insulation upgrade with blow-in cellulose or fiberglass insulation. You can rent an insulation blower yourself or have an insulation contractor do the job, after sealing leaks between the attic and the living space below.  

Beefing up the insulation in your walls is a different matter. In many older homes, walls are framed with 2x4 studs and either have just R-13 fiberglass batt insulation or no insulation at all. Even when there is insulation in exterior walls, there are certain to be air leaks that allow frigid winter air to come into your living space around electrical outlets, window framing and through other air leaks. Flawed installation details can also hurt energy performance. A small void or area where insulation is missing can cut a wall’s overall insulation value by as much as 40%. 

Improving wall insulation can be challenging. After all, who wants to go to the expense of removing interior wallboard or exterior siding and sheathing in order to access a wall’s stud cavities? Another alternative – removing exterior siding and then covering walls with rigid foam insulation—is also expensive and disruptive. So what can be done to solve this energy and comfort problem? 

Injection foam is proving to be an excellent product for upgrading existing wall insulation quickly, affordably and with minimal disruption. Standard two-part foam can’t be sprayed into wall cavities because its expansive force will pop wallboard and sheathing off studs. But injection foam is non-expanding. It’s designed to flow and fill around electrical wires, outlet boxes and existing underperforming insulation. It seals air leaks, fills voids, and provides very high R-value: up to R-5.1 per in. when temperatures are close to freezing.  

To upgrade wall insulation with injection foam, workers drill small (typically 2-in.-dia.) holes in each stud bay, from inside or outside the house. The stud cavity is then filled with injection foam from a flexible hose, and the access holes are plugged.   

Another thing I like about injection foam is that it’s not hazardous to handle. Workers wear safety goggles and gloves rather than respirators and hazmat suits, which are required when installing standard two-part spray foam. Injection foam overspray cleans up with water rather than solvent. 

Recently I watched a crew from a Connecticut-based company called Dr. Energy Saver install injection foam in the walls of a ranch house. Workers removed a course of vinyl siding to access the wall sheathing. After drilling access holes, the injection foam was (there’s no better word) injected into each cavity. The foam looks like shaving cream and has a similar consistency. In just a couple of hours, the job was done. Small amounts of foam were evident inside the house, where the material filled gaps around electrical outlets. Cleanup was easy, and I came away with no doubts about the effectiveness of this technique for sealing leaks and upping wall insulation value. 



Related Content

Microsoft Hohm Application Tracks Energy Use

The new Microsoft Hohm application makes it easy to track your energy use and provides simple recomm...

Success on the Horizon for Lowering Energy Consumption

The future looks bright as long as the United States can follow its current energy efficiency progra...

How to Boil Water ... Efficiently, That Is

What's the most efficient way to boil water?

Weekend Project: Decoupage with Yellow Pages, Paper Bags and Newspapers

What can you do with all those useless newspapers, paper bags and Yellow Pages books? Tear them into...

Content Tools




Post a comment below.

 

ADAM MOSCHETTE
3/21/2012 6:16:29 PM
There is no structural integrity with this product. It is like dried shaving cream. You can easily crush a 3" x 3" cube down to nothing. It only fills voids and prevents airflow. It is not rigid at all. Packing peanuts are stronger.

ADAM MOSCHETTE
3/21/2012 6:12:50 PM
I had this done in my home and it is a fantastic product. The cost was also reasonable. I have a ranch home and I think it cost about $1500. The foam resembles shaving cream and is pumped into the walls using pressure. My house is made from masonry block so one inch holes were drilled into the basement and attic walls. Foam is then injected to fill all voids. I use wood heat and went from four cords last year down to only two. I would highly recommend this product. Tridon Industries in PA did mine and they were great to work with. http://www.tridonindustries.com

David Barlup
12/5/2011 5:12:19 PM
What kind of foam was being used? I'm looking for insulation that is petroleum products free, and haven't found a spray foam that is basically solid gasoline. Trying to seal up our house and make it super efficient

Bill
12/1/2011 12:41:19 AM
Is this something I can rent the machinery and do myself? I doubt I can afford to have someone do it for me on my budget.

FRANCIS PATERNOSTER
11/26/2011 11:29:09 PM
Dear Tim: I had an experence with wall foam insulation 30 years ago when I signed a contract with an insulation company t push wall foam into three of the four walls of myhome in Maryland. Their techs came out, did some measurements, estimated the amount of foam it would take to fill 3 walls, and I signed on the dotted line. When they came to do the job, it took 4 truckloads of foam to fill the gaps, instead of the one they projected. But I still payed the same price for one truckload. per the signed contract. Lucky me, unlucky them! The foam worked great, and has kept the house warm all these years. What a bargain!! JLP, Frederick, MD

Marina Pushkareva
11/26/2011 5:33:42 AM
What kind of foam is used? I remember when company I worked for was offering relocation to employees, company was going to "buy" houses from relocating employees, but only if their houses did not hove polyurethane foam as an insulation...

Daniel Fratus
11/25/2011 3:24:42 PM
I like the idea of using foam because besides insulating the building it would also add to the structural integrity when it cures. This would help the mobile home that I live in a lot assuming that I could level and square it up before foaming.







Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.