If you'd rather burn the smoke from your stove than clean it from your chimney, consider adding a wood stove catalytic converter. A number of companies offer units you can install yourself.
Diagram of the interior of a retrofit wood stove catalytic converter.
Illustration by MOTHER EARTH NEWS Staff
In Wood Stove Efficiency and Emissions: 1984, we reviewed the progress that's being made toward developing clean-burning, efficient wood stoves. The latest high-tech wood burners use 30% less wood and emit up to 90% fewer pollutants than did the best heaters built only five years ago. However, a lot of us simply don't have roughly $1,000 to lay out for the latest catalytic wood stoves.
Luckily, there is a course of action available that's a great deal more affordable than purchasing a complete new wood stove and that still provides much of the efficiency improvement and emissions reduction made possible by these state-of-the-art combustors. There are, you see, over a half-dozen retrofittable wood stove catalytic converter devices on the market today, and test results show that they offer significant performance gains over a plain old airtight heater. If you're in the market for such a device, here are some of the things to look for.
Any retrofit catalyst is a compromise, because the stove that it's installed in was not designed to insure an adequate supply of oxygen and good mixing of the smoke and oxygen at the combustor. Also, add-on catalysts are often positioned farther from active flames than are designed-in units, so the temperature of gases entering them is generally lower. This means that the add-on (and particularly the external) catalyst may be reluctant to "light off" at the beginning of a burn or after refueling.
Catalyst retrofits that are positioned inside the firebox offer some obvious advantages. (We presented plans for a build-it-yourself model in A Wood Stove Catalytic Converter You Can Build.) Their close proximity to the burn zone allows them to get into action early and keep working until there's little left but coals. Having the unit too close to the fire can, however, be a liability. If adequate precautions aren't taken to prevent flames from reaching the ceramic monolith, thermal shock can quickly destroy the catalyst: There have been reports of combustors that disintegrated after only a few months' use in stoves designed without adequate flame impingement protection. Internal combustors are probably best suited to stoves that are used continuously at low to medium heat outputs.
Many designers, including Robert Vincel — who developed the Riteway internal and the Uni-Com external catalyst retrofits — have concluded that the stress to the combustor inside a stove isn't generally worth the gains provided by that position. Vincel's Uni-Com uses elaborate mixing geometry to insure good distribution of gases, and is fitted with cast refractory to give the unit thermal mass. The latter measure helps the combustor get through transient cool conditions — such as occur during reloading — without dropping below ignition temperature.
Tests have been done on three retrofit catalysts by Shelton Energy Research for the New York State Energy Research and Development Authority. The evaluation was limited to one stove design, and Jay Shelton suggests the results could have been different if a variety of appliances had been used. Specifically, some retrofits add secondary air to insure good oxygenation. This could be an advantage on some heaters and a disadvantage on others. Some combustors are longer than others, and the extra length could improve performance on larger stoves with high flue gas velocities. Furthermore, a number of add-ons are also restrictive (that is, they slow the exhaust gases and reduce the maximum burn rate), which may provide better heat transfer in stoves that are leaky. (Restrictions may also protect the combustor by preventing high burn rates and attendant flame impingement.)
But, whether you choose an internal or external catalyst retrofit, there are operating techniques that can help you get the most out of the device. Catalysts thrive on just those conditions that tend to plug the chimneys of conventional airtights with creosote. Once the catalyst has gone into action, it will work best when the firebox is loaded with fuel, the air controls are adjusted for a low burn, and the fire is allowed to smolder. In fact, those of us at MOTHER EARTH NEWS who use catalyst stoves have found that little attention needs to be paid to the heater's operation. A typical day consists of jamming the firebox full first thing in the morning and again before going to bed. A 12-hour burn is within easy reach, and the heat output remains quite stable over that period.
Unfortunately, there's only one way to be absolutely sure that the catalyst is working. Despite all the advertisements that show the combustor glowing, this situation only occurs for, at most, a couple of hours during the burn cycle; most of the time, the catalyst is working just fine without emitting any visible radiation. Only a dual-probe thermometer, with one sensor before the combustor and one after, will show with assurance whether gases are being burned in the catalyst. (Companies that market such devices include Vermont Technology Group, Inc. and Lehman Engineering) A surface thermometer will give you a general idea of whether the combustor is generating heat, but will give little clue to the combustor's overall effectiveness. Of course, a reduction in the amount of smoke coming from the chimney is a general indicator of combustor light-off, and heavy build-up of black, shiny or gooey creosote (rather than tan or brown soot) is a sure sign that the catalyst hasn't been working for some time. Don't assume, however, that a properly operating catalytic converter will eliminate creosote. Some material will still accumulate, and chimney maintenance should be a regular part of your routine.
The list of manufacturers of retrofit catalytic converters that accompanies this article includes most, if not all, of the devices that are presently available for universal application. Many stove manufacturers make kits designed specifically for their products (Riteway is one company that offers such a device), and you should check first with the local dealer who handles your brand of heater. Then, if that fails, consider a universal retrofit. You won't regret it!
External catalytic dampers and catalytic converter retrofits that fit 6", 7", and 8" flues. Top or rear exhaust. Catalytic converter kit retails for $139.95. Five-year limited warranty.
Arden Industries Smoke Genie
An internal catalytic retrofit that mounts in most stoves without internal baffles. Catalytic converter encased in ceramic housing. Seven year limited warranty. Retail price is $199.95.
More than six different models for external and internal retrofit to flue pipes, freestanding stoves with and without internal baffles, top or rear exhaust, and fireplace inserts. Retail from $94.95 to $119.95. Limited warranty on catalyst.
Catalytic Damper Corporation Intensifire
Two external retrofit models: Intensifire 2000 has large combustor and fits 6", 7", and 8" flue pipes. Comes with probe thermometer and five year warranty for $199.95. Intensifire 1000 fits 8" flue pipes (adapters available for others) and has shorter catalyst. Two-year warranty. Retails for $99.95. Adapters for rear exhaust available for either model.
Two external models (P9C and P10C) can be top or rear mounted and fit 8" flues. Adapters allow use on 5", 6", or 7" flues also. Stainless steel wire mesh catalytic converter. Limited one-year warranty.
Internal and external retrofits for freestanding stoves and fireplace inserts. Limited five-year warranty. Top or rear exhaust for 6", 7", or 8" flues. Retail prices from $129.95 to $159.95.
An external retrofit that fits 8" pipes but which can be adapted to other sizes. For top or rear exhaust. Limited one year warranty. Retail price $199.50.
Sotz Retrofit CatalystsExternal retrofits for 6" and 8" flues and for Sotz two-drum stoves. One year limited warranty. Retail (with shipping) $110.97 to $116.97.
Discover a dazzling array of workshops and lectures designed to get you further down the path to independence and self-reliance.LEARN MORE