Boost Your Wind Powered Water Pump With Spring Power

If you use a wind powered water pump on your farm or homestead, you may be able to up the system's efficiency by attaching a big spring.
By Edward Burlbaw
March/April 1981
Add to My MSN

Diagram shows suggested method of attaching spring to sucker rod and the windmill's frame.
EDWARD BURLBAW
Slideshow


Content Tools

Related Content

The Ram Pump

You can move water uphill without complicated pumps and electrical hookups by building a ram pump, w...

Grasshopper Introduces Improved PowerVac Vacuum Collector

The Grasshopper company has introduced the new Model 8HT PowerVac vacuum collector.

Repair Door Trim

Repairing or replacing trim around a door is easy, and you need only a few simple tools.

Photo of the Week: Rodeo Dreams

This little girl is caught up in the rodeo world. Submit your own photos, and you could be the next ...

Folks who attempt to set up a wind powered water pump on a shoestring budget—as I did—may find that, after buying a gearbox, tower, cylinder, and well pipe, there's not much cash left over for a standard "sucker rod." That's what happened to me , anyway, and I had to make do with a substitute. So, after scrounging around, I bought a supply of inexpensive, used one-inch galvanized pipe.

Unfortunately, when I'd completed the system, I found that I wasn't getting anywhere near the rated capacity of the cylinder even in very high winds. I started asking around and, sure enough, discovered that using anything but a genuine sucker rod would add excess weight, thereby overloading the mill and decreasing its output. Simply stated, my galvanized pipe was too heavy.

At first It seemed there was no choice except to buy the "right" rod. However, used wind pumps are scarce and new parts are expensive, so I decided to hold off a bit.

Then, on a trip to Oklahoma, I talked to an old farmer who suggested that I mount a spring to help lift the pumping rod in lighter breezes. He claimed that such a booster can make a real difference in the amount of water a pump supplies. I decided that it was worth a try.

To begin, I chose the biggest spring I could find: an old garage door coil. Using an eyebolt, I connected one end of the spring close to the top of the tower the other end to my sucker rod substitute by means of an old tailpipe clamp and a turnbuckle. The turnbuckle is optional, since the spring tension can easily be adjusted by moving the clamp up or down on the rod.

The spring should be stretched out far enough to support the weight of the sucker pipe, allowing the energy your mill captures to lift only water. So, in order to balance the spring's load, I disconnected my makeshift rod from the gearbox by unbolting the jackshaft from the sucker rod. Common sense told me that when the rod dropped down the spring was too loose, and when the pipe rose the tension was too great. Once no motion occurred, I figured I was all set.

Remember that if your pump has the normal eight-inch stroke, you'll want a spring that—at rest—is at least double that length so it'll exert a more even force through the stroke. (Garage door springs are usually ideal.) Folks with exceptionally deep wells might want to use more than one spring. If you do, be sure to space them equally around the tower to keep the rod centered.

Before I Installed a booster, my pump was producing approximately three gallons per minute in a stiff breeze. With the added spring power attachment my system's per-minute flow has increased to four gallons!

It was an easy modification that certainly paid off for me, and I'm sure other people with "make do" sucker rods on their wind powered water pumpers will find this project to be well worth the effort, too.


Previous | 1 | 2 | Next






Post a comment below.

 

yousef
11/9/2008 2:26:07 PM
I'd like to know a lot about the extraction of water by wind Thanks








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.