Natural Health

Healthy living, herbal remedies and DIY natural beauty.

Add to My MSN

Weekend Project: Garden Bench Made from an Old Tire Inner Tube

3/18/2011 5:31:02 PM

Tags: DIY garden bench, garden bench project, reusing tire tubes, recycled plastic lumber, Susan Wasinger, Robyn Griggs Lawrence

Robyn Griggs Lawrence thumbnailSpring fever is rampant in my neck of the woods. I'm celebrating this weekend by sprucing up my garden area. I've been eyeing outdoor benches at my local garden center, but they're pricey. So this weekend I'm taking on an ambitious project: Susan Wasinger's cute garden bench made from recycled-plastic lumber and an old truck tire inner tube. The bench is comfortable, waterproof and should withstand the harsh Colorado sunshine that bakes my back patio. 




132 inches of 2-by-2-inch plastic lumber, cut into two 12-inch pieces and two 18-inch pieces for the top and four 18-inch-long pieces for the legs (available from Bedford Technology, PlasTeak or Plastic Lumber Company )

Carpenter’s square


8 2-1/2 inch screws

Car or truck tire inner tube

Staple gun


1. For the bench top, assemble a 12-by-18-inch rectangular frame using a carpenter’s square. Predrill the holes and screw the pieces together at the corners.

 2. Attach the legs at each corner joint, using eight 2½-inch-long screws. Position screws so they don’t hit other screws as they enter the lumber. Adjust the screw position up or down to ensure a clear path. For an extra-sturdy bench, add a brace of 1-by-4-inch strips secured with screws about 6 inches down from the top of the leg.

3. To make the bench seat, use scissors to cut about 15 strips, each 2 to 3 inches wide, from the inner tube. Wash strips in hot, soapy water to remove grime.

4. Use a staple gun to tack rubber strips, all going the same direction, underneath the top frame. Double up the material under each staple by putting a small scrap of inner tube under each one. This will make it less likely to tear through the rubber. Stretch the rubber strip across the bench top until it’s very taut, and staple again to the other side.

5. Once you’ve covered the bench top with strips in one direction, begin at the corner and weave another strip up and down through the rows of strips to the other side. Stretch taut and staple. Trim any long ends of rubber.

garden bench 

Made with recycled-plastic lumber and an old truck tire inner tube, this bench is sturdy and comfortable. Photo by Susan Wasinger

Content Tools

Post a comment below.


Bob Bray
8/14/2011 4:13:47 PM
Though I like the idea of reusing inner tubes, if real 2x2 wood was used you'd be supporting a sustainable resource and many businesses.....Tree Growers, Lumberjacks, sawmills and their workers, retail trade in home stores, etc.... Where recycled plastics are not a sustainable resource. To get the used plastic you must get OIL. Pump it from the ground or the seafloor. Oil is not a renewable resource. If we stop or at least reduce using plastic that plastic lumber will not be affordable to make. Yes, I know that the production of both lumber and plastic stuff pollutes the environment, but only growing trees can take CO2 and make H2O. Great idea for a project Still!

8/10/2011 8:07:33 PM
Growing up in Alabama, my old grannyma would use old tire tubes, cut into strips, to re-seat her rocking chair. I still have that rocker but would not trust it to sit on now, I may just re-seat it the same way. You don't have to look for tire tubes, you can buy 3 to 5 bicycle tubes and do the same thing. Thanks for bringing those memories back.

8/10/2011 6:05:16 PM
I used old bicycle innertubes to repair a nice cane chair missing the seat, in a similar way, but a circular weave. Then put a cushion on top. It was good for years.

8/10/2011 4:31:16 PM
Looks like that bench could also be made with old bicycle innertubes!

Subscribe Today!

Pay Now & Save 67% Off the Cover Price

(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here