Build a Movable Chicken Coop

Designed for super-convenient cleanup, this customizable, portable chicken coop comfortably houses up to 15 birds.



Art Of The Chicken Coop
Coop-a-doodle-do! The first step in the increasingly popular hobby of raising chickens is to outfit your birds with a home. “Art of the Chicken Coop” provides detailed instructions for building seven cool-looking coops that range in style from rustic to Victorian and accommodate flocks from six birds to 15. Tossed in throughout the book are handy chicken facts and fun trivia, tasty egg recipes from around the world, and profiles of modern homesteaders who offer advice on living the chicken-keeping life.
COVER: FOX CHAPEL PUBLISHING
Movable Chicken Coop
The inspiration behind this coop was functionality — what kinds of features could be added to make the most practical, easy-to-use coop possible?
FOX CHAPEL PUBLISHING
Movable Chicken Coop Diagram
Coop-a-doodle-do! The first step in the increasingly popular hobby of raising chickens is to outfit your birds with a home. “Art of the Chicken Coop” provides detailed instructions for building seven cool-looking coops that range in style from rustic to Victorian and accommodate flocks from six birds to 15. Tossed in throughout the book are handy chicken facts and fun trivia, tasty egg recipes from around the world, and profiles of modern homesteaders who offer advice on living the chicken-keeping life.
FOX CHAPEL PUBLISHING
Step 1
1. Construct the bottom frame. I began this coop by constructing a frame from 2-by-4s (A, B). To join the parts, I used galvanized angle brackets. I like Rigid-Tie Angle by Simpson in particular because it features a flange that allows screw installation on the inside frame face, which adds quite a bit of stiffness.
FOX CHAPEL PUBLISHING
Step 2
2. Attach the side walls. I built the sides of the coop (C) out of 3/8-inch plywood ripped down to 2 1/2 feet wide. With the frame sitting directly on the floor, it is a straightforward matter to screw the sides (C) to the frame. I suggest spacing the screws about 1 foot apart.
FOX CHAPEL PUBLISHING
Step 3
3. Prepare to add the end walls. Without the end wall panels (D) in place to support the sides (C), the whole structure isn’t particularly strong, and the walls (C) may lean in a bit. This is not a cause for concern — adding the end walls (D) will firm things right up.
FOX CHAPEL PUBLISHING
Step 4
4. Lay out the end walls. The end walls (D) are 3/8-inch plywood. I laid out a roofline as follows. The height of the panel is 3 1/2 feet and the start of the pitch is at 2 1/2 feet, meaning the taper rises 1 foot over a 2-foot-wide span, sometimes described as a 6:12 pitch. I used a framing square to lay out a nice wide door (30 inches by 27 inches) to make clean-out a snap, and I added a small 11-inch-by-11-inch window below the gable for some extra ventilation.
FOX CHAPEL PUBLISHING
Step 5
5. Cut out the end wall doors and windows. When cutting out the doors, it’s important to start and stop the cuts cleanly in the corners so the “waste” pieces can be reused as doors. I used a circular saw for this operation, but a jigsaw would work well, too. The windows aren’t critical — they are such small pieces that it’s easy to find scraps to fit.
FOX CHAPEL PUBLISHING
Step 6
6. Attach the end walls to the coop. Screw the end walls (D) through the base frame (A, B) and reinforce the corner where the wall panels converge by adding interior corner bracing (E). I used 2-by-4s with screws and glue, and I made sure to cut the 2-by-4 shy of the top of the walls so that I would have space to tuck a 2-by-4 cleat (L) in there — more on this later.
FOX CHAPEL PUBLISHING
Step 7
7. Attach the legs. With the shell of the coop assembled, I turned my attention to making and adding the legs (F, G) that hold the coop up off of the ground. These are just 2-by-4s, mitered at the top to match the roof angle (26 1/2 degrees) so the roof sheathing can overhang a few inches. I started with legs all the same length, but you can use lengths marked on the materials list to avoid cutting in the next step.
FOX CHAPEL PUBLISHING
Step 8
8. Locate the wheels. Because I planned to put a set of wheels (H) on the far end of the coop, I had to shorten the legs on that end (G) and drill a hole for the axles (I). If you used 45-inch legs for the back, you won’t need to cut. To lay this out, I lined up the wheel (H) with the bottom of the rear legs (G) and marked for the axle (I). The leg could then be cut a few inches up from the bottom.
FOX CHAPEL PUBLISHING
Step 9
9. Drill the axle holes. I had planned on using a 1/2-inch-diameter axle, so I drilled a 9/16-inch hole to allow just a little bit of wiggle room.
FOX CHAPEL PUBLISHING
Step 10
10. Review your progress. This photo shows how the legs are different lengths. Before installing the wheels, the whole thing actually sloped downhill a little bit.
FOX CHAPEL PUBLISHING
Step 11
11. Mount the axle and wheels. My first inclination was to use an axle that ran from one side of the coop to the other, but the axle sagged more than I was comfortable with. Still, it was a start, and it got the coop leveled out so I could continue working while I brainstormed a solution. However, you may wish to install the 1/2-inch-diameter bolts (I) now.
FOX CHAPEL PUBLISHING
Step 12
12. Cut out the nest box access. The long, back side of the coop is reserved for nest box access. Cut out a large 4-foot-by-1-foot rectangle — you will be using it as a door, so cut carefully.
FOX CHAPEL PUBLISHING
Step 13
13. Hinge the nest box access door. After I installed three hinges, the door worked out great. It allowed for access to all of the nest boxes at once, and putting the hinges at the bottom meant that a person wouldn’t need to use one hand to keep it open.
FOX CHAPEL PUBLISHING
Step 14
14. Cut out the side door. Across from the nest box area, I cut out a large 44-inch-by-24-inch opening for day-in-and-day-out access.
FOX CHAPEL PUBLISHING
Step 15
15. Trim the end wall windows. To trim out the small window on the end walls (D), I used 3/4-inch-thick scraps of cedar (J). I assembled the trim as a unit before mounting to make sure the miters were all tight. When the glue dried, I attached the frames to the outside of the openings and secured them with screws from inside the coop. The opening of the frame is about 1 inch smaller than the window — this hides the plywood edge and creates a more finished look.
FOX CHAPEL PUBLISHING
Step 16
16. Install the bottom. I used 1/2-inch-thick plywood for the bottom (K). The only trick was that I had to notch the corners with a jigsaw so the bottom could fit properly around the corner supports (E). This only took a few minutes and made for a nice result.
FOX CHAPEL PUBLISHING
Step 17
17. Trim the end panel doorways. Trim out the door openings. Set the trim (V) in about 1/2 inch to conceal the edge of the plywood.
FOX CHAPEL PUBLISHING
Step 18
18. Build the nest boxes. This coop was built for about 15 chickens, so four nest boxes was about right. A good rule of thumb is to provide one nest box for every four birds. It was easier and faster to build one large unit and just add a few dividers (W) than to build separate boxes. Cut a wedge off of each divider (W) so the top edge slopes from 15 inches in the back to 12 inches in the front. I put a small lip — the exact height is not critical — at the bottom of the boxes to keep the bedding material from spilling out.
FOX CHAPEL PUBLISHING
Step 19
19. Place the nest boxes. The nest boxes fit perfectly into place and they should work out great. They’re not fastened so they can be removed for cleaning, but hopefully the sloped roof design will prevent perching and the subsequent droppings. This will make for less maintenance down the road.
FOX CHAPEL PUBLISHING
Step 20
20. Install the roof cleats. As I mentioned earlier, I added a 2-by-4 cleat (L) at the top of both side walls (C). This provides a place to secure the lower edge of the roof panels (M). I also installed a 2-by-4 (L) at the peak of the roof as a way to support the top edge of the roof panels. Angle the 2-by-4s so the roof panels (M) will be flat.
FOX CHAPEL PUBLISHING
Step 21
21. Attach the roof panels. The total length of this coop was 96 inches (84 inches for the coop, 6 inches of overhang on each end), so I couldn’t use just one piece of plywood as roof sheathing. This wasn’t a problem — I just cut separate panels (M) and installed them side by side to the underlying 2-by-4s (L).
FOX CHAPEL PUBLISHING
Step 22
22. Staple on the felt paper. As insurance against future leaks, I added a layer of felt paper (U) to the roof and secured it with staples. My trick is to put on pieces of paper slightly larger than the roof and then trim them to size with a utility knife. This is easier than cutting the felt paper exactly to size and then trying to install it precisely — it can be difficult to align if you’re working alone. However, if you’re going to use adhesive in Step 32 (as I do), you should wait to trim the felt paper until then.
FOX CHAPEL PUBLISHING
Step 23
23. Attach the end panel doors. The doors (N) on the end of the coop have hinges at the bottom. It is faster and easier to install one large door than two smaller ones, and it saves a couple of bucks by requiring half as many hinges. Use the wood you cut out in Step 5 if it looks OK. Install a latch on the top of the doors.
FOX CHAPEL PUBLISHING
Step 24
24. Trim out the end panel doors. I trimmed out the edges of the doors (N), but I had to miter the bottom edges of the vertical trim (V) so the door could swing down all the way. A blunt 90-degree cut would’ve gotten in the way.
FOX CHAPEL PUBLISHING
Step 25
25. Install wire on the windows. I stapled chicken wire on the inside of the small ventilation windows. This will keep chickens in and predators out, and the extra airflow will be a real plus.
FOX CHAPEL PUBLISHING
Step 26
26. Install main side doors. The main side doors (O) were hinged at the sides, and I ran a strip of wood (V) up the center to flange over the gap between the two doors. A small brass handle is a nice touch here.
FOX CHAPEL PUBLISHING
Step 27
27. Create the poop tray tracks. I’ve never seen a poop tray built into any other coop, but it’s a really practical idea that saves time during clean-out. The roosts are above a pair of removable trays, so the droppings are consolidated in one place. The trays slide in a simple set of L-shaped tracks (P) made on the table saw. Two cuts on adjacent faces of a 2-by-4 removed the waste material, and I was done in just a few minutes. Note that this operation will require you to change the blade height and fence position between cuts. The exact location and size of the cutout isn’t critical.
FOX CHAPEL PUBLISHING
Step 28
28. Install the tracks. Install the tracks (P) parallel to each other about 18 1/2 inches to 19 inches apart, using a series of countersunk screws.
FOX CHAPEL PUBLISHING
Step 29
29. Create the poop trays. The trays (Q) themselves are 18 inches wide by 40 inches long. I considered putting a handle on the end, but I figured a simple hole would function just as well. I used a 1-1/4-inch-diameter spade (or paddle) bit to make the holes.
FOX CHAPEL PUBLISHING
Step 30
30. Make the roosts. The roosts (Y, Z) are lightweight and removable, and they fit neatly atop the trays. You could build them in two sections, but I didn’t see a downside to building a single long one. Screw the long dowels (Y) into the roost supports (Z).
FOX CHAPEL PUBLISHING
Step 31
31. Install wheel supports and permanent axles. As I worked out a good way to support the wheel, I considered welding up something akin to a bicycle fork, following the logic that the wheel needed to be supported on both sides. I then realized that adding a 2-by-4 (R) would do the trick just fine, and 7-inch-long bolts with lock nuts (I) held everything in place quite well.
FOX CHAPEL PUBLISHING
Step 32
32. Apply roofing adhesive. When it came time to install the roofing, I cut back the felt paper (U) a few inches along the edges because I wanted to put in a layer of adhesive to secure the roll roofing to the sheathing (most home improvement stores carry an inexpensive product for just this purpose).
FOX CHAPEL PUBLISHING
Step 33
33. Apply the roofing. Rolling out the roofing (T) by yourself is tricky, but if you keep it rolled up and then secure one end with staples, you should be able to manage it. When in doubt, get help.
FOX CHAPEL PUBLISHING
Step 34
34. Clamp the roof and let dry. The adhesive needed a couple of days to set up, so I clamped the edges down with a caul and a simple spring clamp. I secured the middle section of the roofing by nailing it directly to the sheathing at 1-foot intervals.
FOX CHAPEL PUBLISHING
Step 35
35. Trim up the roofing. As with the felt paper (U), it is much easier to roll out the roofing material (T) if you have some extra width — the excess can be trimmed off with a utility knife.
FOX CHAPEL PUBLISHING
Step 36
36. Cover the windows. To seal up the windows, I cut a pair of square panels (AA) out of 3/4-inch plywood and attached them to the frames (J) with hinges. A little decoration never hurts, either — I used a scrap of wood and a chicken stamp I had.
FOX CHAPEL PUBLISHING
Step 37
37. Examine the window covering. The hinges on the left side of the window cover (AA) look neat and clean.
FOX CHAPEL PUBLISHING
Step 38
38. Shape the handles. As I wound up the process, I turned my attention to designing a set of handles that would enable the coop to be moved around easily. I used a pair of 40-inch-long 2-by-2s and rounded over their edges with a router to make them easy on the hands.
FOX CHAPEL PUBLISHING
Step 39
39. Attach the handles. The handles (S) are easily attached to the coop by drilling a pair of 1-3/4-inch holes in the bottom corners of the end wall (D). The handles are then inserted and screwed into the floor of the coop with a couple of long, 2-inch screws.
FOX CHAPEL PUBLISHING
Step 40
40. Examine the handles. The limiting factor seemed to be the distance between the handles — if they were closer together, one person would have an even easier time maneuvering it, but that wasn’t really much of an option because the door takes up most of the real estate in that area. Even so, it worked quite well.
FOX CHAPEL PUBLISHING











Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.