Masonry Heater: The Russian Fireplace

Build a stone masonry heater as a home heating device, including masonry tips.
By the MOTHER EARTH NEWS editors
November/December 1983
Add to My MSN

Smoke rises from the firebrick flue, curls down the sides, and exits from the bottom rear.
Photo by MOTHER EARTH NEWS staff
Slideshow


Content Tools

Related Content

When Building Post and Beam in Straw Bale, Can I Substitute Concrete Block Columns for the Wooden Posts?

Concrete block columns aren't typically used in straw bale buildings, but here's how you can make it...

Tips for Heating with Wood

When it's cold outside, who doesn't love a cozy fireplace or woodstove? Wood heat is a comfortable w...

Sealing The Cracks

Tightening up our log cabin with a mortar mix.

A Sense of Accomplishment

Cam enjoys a sense of accomplishment many times a day as he uses his sidewalk!

As a matter of fact, steel and iron have a number of disadvantages when it comes to providing a housing in which efficient, clean combustion takes place. For one, neither material has a high heat-storage capacity when compared with any cement mixture. Consequently, the output of a metal appliance all too closely mirrors the inconsistent burning conditions inside the heater. Furthermore, steel and iron have a high rate of heat transfer. Now that's a fine thing in the right place (after all, you do want that warmth to get into your house, not out the chimney!), but inside the firebox too rapid dispersion of heat can result in reduced combustion efficiency-possibly even quenching the flame sand increased pollutant emissions. And finally, metal heaters have a relatively short life span, while — as anyone who lives in an old house with fireplaces can attest — masonry products survive very well under the adverse conditions of coal or wood burning.

Heat for the Masses 

Those of you who are regular MOTHER EARTH NEWS readers are probably already aware that a Russian fireplace solves many of the problems inherent in metal wood stoves and provides an effective source of heat. A massive masonry heater is efficient, clean, and requires a minimum of upkeep. Still — as you may also remember — our Russian fireplace is built of more than 1,000 bricks, and has developed a number of cracks (none yet leaks smoke, though). Properly assembling such a huge heater is a complicated and time-consuming enterprise. Indeed, in many parts of the country today, masons are charging upward of $3,500 to build one.

All of this leads to a have-your-cake-and-eat it question: Is it possible to have a good masonry heater that's not too troublesome or costly to build? That's what puzzled Fred Fitzpatrick, an apprentice of Albie Barden (who's one of the renowned experts on massive masonry wood burners). Fred learned the liabilities of brick as a material for building Russian fireplaces when he assembled more than a dozen such heaters in his Groton, Massachusetts area ... including one (which Albie helped him erect) in his own living room. So Fitzpatrick — a fount of energy who builds masonry heaters as a sideline from his vocation as a biology teacher at a Boston inner-city school and from his avocation as a naturalist and leader of river trips in the region — began looking for a better approach. And what he's developed, we think you'll agree, is just that!

Masonry for Nonmasons 

Fred had a clear set of goals in mind when he began to search for an alternative to the common brick: First, he needed something that would allow a masonry heater to be built quickly in spite of its convoluted heat exchange path. (With all of his occupations and hobbies — including cooking gourmet meals for a budding family, raising livestock, and maintaining an ambitious garden — this man doesn't have time on his hands!) An equally important constraint was the need to cut down the two- to four-month curing time required for brick heaters. In addition, the material had to be easy to work with, since Fred had already determined that his own masonry bent was more structural than decorative. And last, the ideal "ingredient" would also be capable of withstanding greater thermal stress than brick can, to allow rapid and extreme heating without attendant cracking.

Refractory concrete was the obvious choice. It could be cast in a backyard . . . mixed to cure sufficiently in a very short time . . . and expected to withstand intense thermal stress. So, by applying some of his graduate training in chemistry and an equal dose of experimentation, Fred came up with a special refractory cement mixture. He designed his own forms — set on a specially leveled concrete platform — to produce the largest blocks that he could handle practically: 150-pound segments. The steel molds in which the blocks are formed have keys built in so that the sections can be laid up to interlock . . . yielding a masonry box that's 48" square on the outside. In addition, special forming sections produce blocks with round holes for stovepipe exits and with notches to which the cast-iron doors (which Fred also designed) can be mounted.

The 17" X 19" X 36" firebox consists of five special blocks, made from a somewhat different mixture, each of which weighs well over 200 pounds. The smoke exits from the top of this inner chamber into a rectangular flue (built up from firebrick) that leads to the roof of the heater. From there, as in the Finnish contra-flow design, the gases are forced to flow down the side walls of masonry and exit from the fireplace through an exterior round opening that's beneath the firebox. A combination of stovepipe and insulated factory-built chimney is then used to exhaust the combustion products from the house.

How Quick? 

After more than three years of testing, Fred finally decided to go commercial with his Russian fireplace. So in late May of this year, one of MOTHER EARTH NEWS' staff members visited Fitzpatrick's home-based operation for a firsthand look. Our staffer participated in the construction of a Russian fireplace, and got to see for himself the speed with which one can be assembled. The blocks for this particular heater were cast Friday evening after Fred got home from school (the project was begun by his neighbor, Ron Stanton) and on Saturday morning. Saturday night, Fred and his newly conscripted assistant (MOTHER EARTH NEWS staffer) loaded the roughly 3 1/2 tons of concrete blocks into a stake bed truck, along with tools, mortar, a wheelbarrow, and various other items. And by 6:00 AM the following morning, they and mason's assistant Tom Krause were on their way to the Southwest Corridor Community Farm and Greenhouse in Jamaica Plains, Massachusetts.

Work commenced shortly before 8:30 AM, as the first course of blocks was buttered (with a mortar made up of more refractory cement) and laid onto the 4 1/2' square slab that had previously been poured in the greenhouse. With one full-time helper and another "composite" one — in the form of either Leroy Stoddard (the farm manager), Bob Rochlin (one of Fred's fellow teachers), or our staff member — the heater rose quickly through ten courses. In less than four hours the lid of ceramic insulation, steel plate, and cement slabs was in place! According to Russian fireplaces' proprietor, the heater could have been fired the following afternoon, if necessary.

A completely installed Russian fireplace now costs between $2,200 and $2,500 . . . as compared with the $3,500 that Fred used to charge for the material plus two weeks of labor needed to build a massive heater from brick. The customer not only saves $1,000, but also gets what Fitzpatrick considers to be a superior appliance. What's more, the rapid and strenuous construction suits Fred's own inclinations. He moves ten tons of block on an average working weekend . . . a work load that's used up numerous relatives and assistants. Fred doesn't seem to mind all the lifting. Rather, he points to an advantage of building the hefty heaters: "They're guaranteed against theft."

Performance 

Fitzpatrick's own household actually has two Russian-type fireplaces now. There's the original brick unit that Fred assembled with Albie Barden back when the family was building its 3,000-square-foot gambrel-roofed home, and there's the Russian block one that Fred built in the basement in the summer of 1981. Through the winters of 1982 and '83, their home was heated exclusively by the basement unit, and the residents kept records of temperatures and loading procedures.

Unlike brick-built heaters, Fred's Russian stove's ample firebox can be loaded with large logs. A typical fire consists of six 6" X 36" pieces of pine that burn so rapidly they're reduced to coals in only 45 minutes. During that initial intense fire, the temperature on the inside wall of the firebox will reach 1700 degrees Fahrenheit . . . yet the gases exiting the stove will be only 170 degrees Fahrenheit! This loading procedure is repeated twice more to raise the exterior walls of the heater to 230 degrees Fahrenheit. The heated mass can then maintain the Fitzpatricks' house at a comfortable temperature (in January) for 21 hours.

Of course, the huge heat-exchange area available in a massive masonry heater results in very high heat-transfer efficiency. In addition, the high-temperature burns produce extremely efficient combustion . . . with the side benefit of almost no creosote deposit. (Fred has never had to clean his chimney.)

And for the Fitzpatricks — and other Boston area owners of Russian fireplaces — there's a further benefit to this efficiency and cleanliness: They can burn "low grade" wood. People with metal heaters avoid using pine and green hardwood because of those fuels' reputations for creosote production and low heat content. This prejudice goes so far that local tree trimmers and contractors clearing land must pay a substantial sum to dump such wood at a landfill, but Fred and his customers generously allow the cutters to leave piles in their yards . . . as long as the trees are trimmed to 36 inches in length. Consequently, over the last three winters, Fred hasn't had to cut or purchase any fuel wood, and only rarely does he need to split pieces to fit them into his heater.

And that fuel delivery service leaves Fred free to put his prodigious energies into building more Russian fireplaces . . . so that, for a very reasonable price, other people can spend their winters in cozy comfort.


Previous | 1 | 2 | 3 | 4 | Next






Post a comment below.

 

Rich_23
1/14/2010 11:06:08 AM
The best resource for do-it-yourself masonry stoves is http://mha-net.org You will find plans there and many excellent examples of masonry stoves. Also, the organization (the Masonry Heater Association) sponsors several workshops every year.

hhunt
1/14/2010 9:38:37 AM
We do not have the plans for the masonry heater from this 1983 article. See the note at the end of the article for information on DIY plans.

Curtis_4
7/12/2009 11:59:42 AM
Please persuade Fred to put together a how to book on building the Siberian fireplace. I would be his first customer.

Jim_8
2/18/2009 5:01:34 PM
How can I recieve plans for this stove? jim

hhunt
10/28/2008 1:06:07 PM
You can find the construction illustrations in the Image Gallery at the top of the article.

steve_6
10/28/2008 1:01:56 PM
any body know how to get plans for this fire place????

CShav10
10/27/2008 9:12:11 PM
I've been using one of Fred's Siberian Stoves in my house for the last 20 years. It is by far the best investment I ever made. I light one fire a day most days--two on the coldest days of the year in Pennsylvania where I live. The mass of the Siberian Stove takes about 3 hours to begin radiating the heat out into the house. But it does so for nearly a full 24 hours after the fire was built. The heat is gentle and you can lean against the stove when you come in from the cold to get warmed up. It never gets overly hot to the touch. Aside from solar heat, which I also use, it is the best source of heat...and the best $2500 I ever spent. 20 years service without any problems at all!

Ken_18
4/21/2007 6:58:59 PM
I have been trying to get plans for the Siberian Fireplace. Can I get the kit. Please let me know. Thanks, Ken Holden








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.