Learn how to construct a tipi with a step-by-step guide and tips.
With centuries of use, tipis are among the best, natural living spaces.
ILLUSTRATION: MOTHER EARTH NEWS STAFF
For more than 400 years, knowledgeable people have agreed that the Plains Indian tipi is absolutely the finest of all movable shelters. To the Indian — whose concept of life and religion was broader, deeper, richer and infinitely more unified than that of his white conqueror — the tipi was much more: both home and church, a sacred place of being and sharing with family, friends, nature and Man-Above.
Unfortunately, the white man — with a fragmented and neatly compartmented view of existence — found the all-encompassing Indian way literally "beyond understanding" and, therefore, of no consequence. This high-handed and naive judgment extended, of course, to the lodges of the Plains Indians.
In the "either-or" white mind, the tipi was flimsy and primitive when compared to a solid, substantial frame building. The fact that a tipi was bright, open, airy, warm, dry and easily transported over (and, therefore, a part of) all outdoors while the frame structure was — and largely remains — closed in, dark, poorly ventilated and rather pathetically rooted to one spot was completely beside the point to this schizoid way of thinking.
Luckily, our "civilized" appraisal of the Indian way is now going through some changes and that more reverent life style is increasingly understood and embraced by the new gentle people. As one result of this trend, the tipi is enjoying a sudden popularity.
The tipi is not the final answer for everyone, of course (even the Plains Indians built other structures), but it remains — time, money and labor vs. comfort, utility and versatility — probably the world's most efficient shelter. If you've ever wanted one for camping, semi-permanent or even permanent living, here's how to make it happen...
There are two basic Plains Indian tipis: One uses three foundation poles and the other has four. Our plans are for the three-pole design which is simpler, stronger and — in general — superior to the four-pole model. The dimensions given here are largely taken from the Sioux tipi pattern presented by Reginald and Gladys Laubin in their University Of Oklahoma Press book, The Indian Tipi.
Just to get it straight right in front, the Laubin book is the authoritive work on the Indian tipi and contains a wealth of information on the construction, tradition and lore of the tipi that you won't find here or anywhere else. We're going to give you detailed instructions on making, pitching and living in a tipi. But, if you really want to learn about this shelter, you've got to read The Indian Tipi.
Indian tipis varied from slightly less than 10 feet in diameter, for hunting expeditions, to permanent lodges with a diameter of more than 30 feet. The larger structures naturally required more and longer poles than the smaller ones. We've compromised on a tent diameter of approximately 18-1/2 feet (roomy but easily transported by car) and — for this size — you'll need 17 poles about 25 feet long.
The 15 poles used in the frame should be three or four inches thick at the butt and two inches through where they cross and tie. The two smoke flap poles need be no thicker than two inches at the butt. The best poles always come from a young, crowded stand where each tree has grown tall and slim reaching for the sun.
Red and white cedar make exceptionally light, strong supports which were prized by some tribes. Lodge-pale pine (guess how it got its name) and western yellow pine are both heavier but still make good tipi supports. If none of these are available, use the best timber you can find for the job or buy some fast quality 2-by-4-foot poles, rip them lengthwise on a taper and round the corners with a draw knife or joiner.
If you do find some suitable timber, cut the trees early in the spring (remember, when selecting, to allow for removal of bark and shrinkage) and trim off all knots and branches "up the tree" with an axe or chainsaw.
Lay each pole across two sawhorses (small blocks nailed to the horses 4 inches apart will keep the poles from tuning) and, starting at the butt, straddle the pole and peel it with a sharp draw knife. Season the peeled poles by laying them flat across pieces of scrap lumber spaced two feet apart on a patch of open ground. Let the pores air and sun cure for three to four weeks. Turn them regularly so they season out straight and true.
The Laubins recommend a good application of pentachloraphenol, log oil or floor hardener to preserve and protect the finished poles. If you're on the non-chemical trip, you may prefer to let the wood age naturally or compromise on a couple coats of linseed oil rubbed in.
A properly tanned hide tipi cover was a beautiful creamy white and you're going to want a white, pearl grey, yellow or other bright canvas for your cover. The colored canvas — blue, green, brown and olive drab — so dear to the hearts of most tent makers is not at all traditional and will make your finished tipi dark and dreary inside. The coated "modem" fabrics also shut out too much light and the Laubins have found that muslin exposed directly to the sun has a short life. So a light colored, light weight canvas it is.
If you can obtain an 8 or 10 oz. duck canvas in 72-foot width, you'll save some work and your tipi will have fewer seams. It's hard to find canvas that wide, however, so we're basing our design on a fabric of 36-foot width.
Shop around. I priced waterproofed 8 oz. duck from $1.10 to $1.75 and 10 oz. at $1.25 to $2.00 at a running yard in Cleveland while writing this article. I believe I could have found lower prices if I had really gotten into it, so use the old purchasing agent's rule of thumb: Always get at least three quotes before making any major purchase.
1. Cut six pieces of 36-foot wide, 8 or 10 oz. canvas (8 oz. is much easier to work, makes a lighter tipi and is less expensive) 38 1/2 feet, 38 feet, 36 feet and 7 inches, 34 1/3 feet, 30 feet and 10 inches and 25 feet and 10 inches long.
2. Find the center of each piece and spread out the canvas (as shown in figure 1 of this story's image gallery). The strips should be laid together like shingles on a roof so water will run off, rather than under, the seams.
A flat seam, like dressmakers use on a shirt, is recommended for sewing the strips together. If you intend to "farm out" this part of the job, try to find a tent maker who will use flat seams. I'm sure there's a better way... but here's a method we worked out for sewing such seams:
3. When all six strips are sewed together, lay the cover out flat again and locate the center of the upper (longest) strip. Measure down 20 inches from the top edge of this strip and out 8 1/2 feet both directions from its center line. Cut off and remove the 20 inches by (approximately) 10-3/4-foot rectangles from the two upper corners of the strip. Note that the cut made perpendicular to the edge of the canvas is extended to a depth of 24 inches even though the piece removed is only 20 inches deep. The extra four inches will later be turned under for a hem.
4. Sew the two removed panels into one strip. Center and attach this long narrow piece to the bottom of the 25-feet and 10-inch strip. This will extend the whole canvas enough to allow you to chalk and cut a 19-1/4-foot radius from the center of the top edge of the tipi cover.
5. Set a peg at point "X" and swing your chalk on a length of cord that will not stretch. You can also drill a hole for the peg in a board or piece of plywood, drill a second hole for the chalk in another and nail the two sections to a 2-by-4 so that the holes are the proper distance apart.
The selvage on tent canvas — unlike the selvage on most other fabrics — is not cut off and removed. This means that your 36-inch wide material is actually 37 inches wide. The pattern we are using was designed to give you the most tipi from the least material and — if your six seams across the cover are one half to three-quarters of an inch wide — the 19-1/4-foot radius will not run off the bottom edge of the pieced-together fabric. If the radius does run off the bottom, don't worry. Just cut another scrap and piece out the bottom center a little farther or pull in the string and make the radius 19 feet and 1 inch or 19 feet and 2 inches. You'll never notice the slight difference in final tipi size.
6. Directly below "X", on the first seam, measure 3 inches each way from the center line (total of 6 inches) for the base of the tie flap. Cut from these points straight out to point X. Trim and hem the resulting long, narrow triangle (6 by 24 inches) to a flap 6 inches wide by 8 inches long (as shown in detail 3a).
The four inches (difference between 20 inches and 24 inches) allowed when the corner panels were removed from the top of the cover can be turned down and pinned while a half oval is cut from each side of what will become the tipi's front. The half ovals will later form the door of the shelter and each cut should finish out, after hemming, approximately 46 inches long by 10 inches deep and be located 12 inches in from the cover's outside radius.
The four inches down each side of the tipi's front can be permanently turned and hemmed before or after the door halves are cut and finished out. If you are — or can procure the services of — a good seamstress, you may want to put a facing around the door ovals and then hem the front edges. When you do sew this hem, be sure to make it only 3 1/2 inches wide with the extra 1/2 inch turned under again (detail 3b) so no raw edge is left exposed.
7. After the 3-1/2-inch hem is finished, lay out, cut and stitch in the lacing pin holes below the door opening and between the door and the base of the smoke flaps.
The holes on the left side start 3/4 inch from the hemmed door and the two rows are spaced 1 1/2 inches apart with the outside row set 3/4 inch from the edge. Use the same edge distance for the holes on the right side, but space the two rows 2 inches apart. The 1/2 inch difference will make lacing pin insertion considerably easier and neater when the right side is lapped over the left.
The Laubins recommend a vertical spacing of 7 inches between each set of holes although — if you like a lot of tedious hand work — you can space them as close as 4 inches. Note that it is not necessary to run the holes all the way to the base of the smoke flaps. Tie tapes, added later, will be better than lacing pins for closing that space.
To make each hole, cut a little cross with quarter inch arms in the canvas and buttonstitch around it with No. 10 unbleached shoemaker's thread coated with beeswax (detail 3c). If done properly, this will make a 3/8-inch diameter, self-reinforced round hole and no grommets will be needed.
8. The top horizontal piecing seam is now opened for 39 inches on each side of the 6 inches base of the tie flap. A gore of 39 by 39 by 7 inches finished size (with one inch added all around for seams) is sewed into each opening (detail 4a). Flat seams, again, are best and you'll probably prefer to sew in these gores by hand.
The Laubins rightly claim that all other popular writers on the tipi have overlooked these gores which so greatly help the finished cover fit around the tipi poles. Other authors, such as Seton, show the flaps cut wider at the top — but that's not the same thing at all. The Laubins deserve full credit, to my knowledge, for bringing this important detail to light.
9. An 8 by 24-inch (final size) extension is now added to the base of each smoke flap (detail 4b). These 8-inch extensions are more authentically Cheyenne than Sioux. The Sioux only occasionally added extensions of no more than 4 inches. This slight deviation from a strictly Sioux pattern really helps to "weathertight" a tipi during heavy storms, however, and is a worthwhile addition. Again, allow for hemming the flaps and sewing them on with a flat seam.
10. Some pole pockets, cords and reinforcing added to the smoke flaps will now complete the tipi cover. For each pole pocket, cut two or three thicknesses of canvas, sew (as shown in detail 5a) and attach firmly to the upper corner of the smoke flap. A switch of human or horse hair fastened to the tip of the pocket makes a traditional decoration.
11. Sew two tapes, each 3 feet long, to the tie flap and an 18-inch long tie tape to the base of each smoke flap. The tapes are made by folding together a 3-inch-wide strip of canvas into a triple-thick 1-inch-wide band that is double stitched down both sides (detail 5b).
Note that the tape on the base of the left smoke flap is sewed to the top side of the hem and the right smoke flap's tape is placed on the under side of the hem. This is not a mistake. When the cover is in position with the right side lapped over the left, the tapes will be properly positioned for easiest tying.
12. Buttonhole stitch a small hole in the lower corner of each smoke flap and attach a 3/16-inch cord 16 feet long. (The crosshatching on figure 5 indicates four layers of reinforcing stitched by hand to the under side of the cover in the areas of main stress. This reinforcing is essential.)
13. As a final reinforcement, you can sew a length of 3/16-inch cord around the tie flap and along the top edge of the smoke flaps. Use the same shoemaker's thread you used for the buttonhole stitching and sew over and over (as shown in detail 5c). It is not necessary to hem the bottom of the tipi since the cloth — cut on a bias — will not ravel. This again is traditional as the Indians themselves seldom hem their tipi bottoms.
The tipi cover is now complete but, if you were to stretch it over a set of poles and peg the bottom down, you'd find the resulting shelter no more comfortable than the average white man's tent. Wind would blow in at the bottom, rain run down the poles and drip on everyone and everything, smoke from an inside fire fill the structure under most conditions and moisture condense inside on every cool night. The tipi would be hot in summer, cold in winter, dirty, drafty and damp: In short, it would be unsuitable for camping and unfit to live in for extended periods — just like most white man's tents.
One simple modification — the addition of a liner — changes all that, however. With a liner and a little common sense, the Plains Indian tipi becomes warm and snug in winter and cool and dry in summer. A fire built in the center draws properly and dew no longer condenses inside. There's no draft, no dampness and no more dirt in the living area than in the average summer cottage. A liner, in other words, almost magically transforms the tipi from a tent into a home.
The liner, which might be described as "a tipi without a top within a tipi," is very easy to make (figure 6 gives all the basic information you'll need).
Fifteen identical tapered panels — each six feet long, 34 1/4 inches wide at the top and 48 3/4 inches across the bottom — will be needed to make your liner. The panels can be made from any lightweight material but it is more important that the finished liner be waterproof than that the tipi cover itself be so treated.
Since it will not be exposed directly to the sun, the Laubins recommend using heavy bleached muslin here and treating the finished liner with a wax compound. Balancing tradition and reasonable cost against other considerations, that seems a good way to go although some of the newer coated fabrics should be very attractive to folks with a healthier pocketbook. There's nothing wrong with 8 oz. duck canvas, either.
If you can't obtain the muslin or other fabric in a 72-inch width, 36-inch material sewed together with a flat seam will work quite well.
Cut the panels (reversing every other one to save material, as shown in detail 6e), seam them together and hem the top and bottom of the liner. If you rough cut all 15 sections 34 1/2 to 35 inches across the top and 48 1/2 to 49 inches at the bottom, the finished liner should go completely around the inside and lap generously, depending upon how the poles are placed, how tightly the liner is tied, etc.
The Laubins — who have lived months or years in a tipi to my days in these shelters — have refined their liner design (as noted in figure 6). They recommend cutting only 12 of the 15 panels (C through N) to the full 34-3/4-inch top and 48-3/4-inch bottom dimensions. (Sections "B" and "O," they say, should measure just 31 3/4 inches across the top and "A" should be cut 29 inches across the top and 41 inches at the bottom for a neater fit.)
A double 3/16-inch cord and reinforcing patch added across (detail 6f) — or tie tape sewed into — the top and bottom of each vertical seam will complete the liner. If you use cord for these ties, it can also be fastened to the fabric in the traditional string-around-a-pebble manner shown for attaching peg loops. (See the center detail on figure 7. This may be the best way of all because of the flexibility of locating the ties and the ease with which they may be changed — another example of the sophistication and practicality of the Indians' seemingly primitive methods.)
Make each free end of the ties 24 to 30 inches long. Note that the lower set of cords is located 6 to 8 inches from the liner's bottom edge and the last bottom tie (in section "O") is set in from the outside vertical edge. This allows the bottom of the liner to be turned in all the way around and the meeting ends to lap. You'll find it easier to locate that last tie (on "O") after the liner is hung for the first time.
Some tipi owners prefer to tie the liner directly to the poles (details 6a-b) but if you do, remember to insert two little twigs under each tie on the inside of the supports. This allows stray trickles running down the support to keep right on going instead of dripping off at the tie point.
There is another drip-free method of hanging the liner: A quarter-inch rope is stretched tightly from pole to pole and wrapped around each support so that it runs inside, rather than next, to the cover. The liner is then tied to the mid-point of each span of the rope. The base of the lining is tied to the butts of the tipi poles, to the pegs used to hold down the cover or to a separate set of pegs.
Since the prevailing winds on the Plains are from the west and southwest, the tipi — with only a few exceptions — was always pitched facing east and the following directions are for pitching one that way.
Look for a well drained, smooth, level area and remove all roots, stones, etc. Although a tipi can be comfortable in the broiling sun, you can pitch yours to the northeast of a tree or trees in the summer for late morning to evening shade, if you wish. Don't locate directly under trees because they can be dangerous during storms and drip for hours after a rain.
The floor plan of a properly pitched tipi is oval or egg shaped, rather than round (figure 7). The tipi cone is also tilted and steeper up the back than the front. This is a main secret of the tent's comfort.
If the tipi were an evenly balanced cone, the smoke vent would center around the poles where they cross and would be too large to close completely during a rain. By changing the floor plan and tilting the cone, the Indians were able to extend the smoke hole down the elongated front of the tent. This placed the crossing of the poles at the top of the smoke hole instead of in the middle and allowed the opening to be easily closed with the protruding flaps. It also moves the fire slightly toward the front of the tipi, which makes more efficient use of the tent's interior.
Pick out the four heaviest poles. Three will be used for the foundation tripod and the fourth will be the lifting pole. Spread out the tipi cover and use it to measure the tripod poles (as shown in the upper left corner of figure 7). Note that, since the finished cover is not a true half-circle, this method automatically and correctly locates the tripod tie point lower on poles N and S than on pole D (remember, it's a tilted cone).
Good tipi poles are sharpened on each end. If you intend to plant the butts of the tripod poles a few inches in the ground (as some, but not all, Indians did), allow for that right now and mark the three supports where they cross so you won't have to remeasure every time you erect the tent.
Using one end of a 45-foot length of 1/2-inch rope, tie the three poles with a clove hitch as illustrated, wrap the rope around the poles three or four times and finish with two half hitches.
Put the butts of poles S and D about where they'll be in the pitched tipi and, while someone holds taut the loose end of the 1/2-inch rope, raise the tripod by walking up under the ends of S and N. When the poles are almost vertical, swing the butt of N across to it's approximate final position. This locks the tripod and gives it a twisted dog-chasing-its-tail appearance where the poles cross and are tied.
As nearly as possible (it will be pure trial and error the first time), position the poles exactly as they'll be when the tent is completely pitched. The 2-1/2-foot by 2-1/2-foot grid on one floor plan in figure 7 will help. Note that this tipi measures 20 feet from front to back and 17 1/2 feet across. Notice also, that the tipi's pole pattern is shifted just slightly off square around the perimeter clockwise.
Set the next 11 poles into place exactly in the order shown: 1, 2, 3 and 4 from the right, or north, side go into the front crotch first; 5, 6, 7 and 8 then stack into the front crotch from the left, or south, side and 9, 10 and 11 are put into the back crotch last. Again, strictly follow this order and be sure to skip a place on the perimeter at "L" for the lifting pole. The pole pattern should now look like figure 7's lower right drawing.
At this point, carry the 1/2-inch rope outside the frame at pole S and wrap it clockwise four times (the sacred Indian number) around the standing poles. Snap the rope tightly up into the area where the poles cross and bring it in over N. Angle a 2-by-2 peg 3-feet long into the tipi floor slightly behind center and snug the rope under it. It helps if the peg has a knob on top.
Lay the lifting pole down the center of the cover and mark it at the tip of the tie flap. Put the pole aside and fold the outside edges of the cover in to the center so that the lacing pin holes meet down the center line. Fold and refold both halves of the cover on themselves until each is a long triangle two feet wide at the base. Fold the two triangles together.
Put the lifting pole alongside the canvas, butt to the base of the bundle, and securely tie the tapes (wrapping them over and over the flap in a criss-cross) to the pole where previously marked.
Hoist the pole and canvas (you may need help), set the pole's butt into position and drop it into the last space in the rear crotch. Turn the pole as you lift it and let it fall so that the cover is always on top. If the cover fits too high or too low where the poles cross, swing the lifting pole back down and relocate the tie flap tapes.
Unroll the cover around each side of the frame to the front. Tie a pole (the one you'll later set in front of the tipi door) across supports D and F1 to stand on while you tie the smoke hole base tapes together and insert the top lacing pins. The cover should be slack enough to allow you to lap the south (left) over the north (right) side. Remove the cross bar as you button down the front of the tipi.
Insert the poles in the upside-down smoke flap pockets. Cut these poles just long enough to stretch the flaps tight when their butts cross or barely touch close against the back center line of the tent. Round the pole tips to protect the flap pockets.
Loosen the smoke flap poles so they just help hold the cover even and begin pushing the frame poles out against the cover. Do not push the poles out tightly until the cover is properly pegged down, but do space them out evenly to aid in locating the pegs. By the way, as soon as you're sure the tripod is placed correctly, set the three poles with a shovel, if you intend to set them.
The peg loops are 3/16-inch cord tied in a square knot around a 3/4-inch pebble 6 inches above the cover's lower edge. Tie the loose ends of the cord into another square knot, insert and twirl a peg to twist the cord tightly into a no-slip grip. Peg down the front, then the rear and both sides of the cover. Use a sledge and long iron rod to make lead holes for the pegs in hard or rocky soil.
Now push the poles tightly out against the cover (loosen the anchor rope for this, if you have to). For a permanent camp, plant all the tipi poles by loosening a few pegs, digging under a pole, twisting it into the ground, replacing the pegs and moving on around the circle. If you find the door pole is too long, as sometimes happens the first time a tipi is raised, plant it deeper or chop it off. If you chop it off, of course, it will cause no trouble next time.
Spacing the poles for the first time is the hardest part of pitching a tipi. Once you get them right, swing a cord off the center peg and measure the distance out to each one. Write the figures down and use them the next time you erect the tent. You'll also find that smoke from fires in the tipi will darken the cover everywhere but directly behind each pole and you'll soon be able to line up the supports with the white stripes on the canvas. Once you've got them, retie the anchor rope.
Set a 6- or 8-foot pole in front of the door to tie the smoke flap cords to — and your tipi is up. The door itself — a piece of canvas laced over a willow rod frame — is hung from the last lacing pin over the doorway.
A little study of figure 8 will give you the basics of living year-round in your tipi. Set the smoke flaps quartering downwind under any given conditions and you should have little trouble making an inside fire draw properly. Stick up a brush windbreak and pile small logs around the bottom of the cover in the winter. This is nothing unusual for the Plains, you know: People there still stack bales of straw around the foundations of frame houses during the cold months. Roll up the tent's sides and take down the liner on still, hot summer days. And don't be too proud to cut a few boughs and lean them against the sunny side of the shelter on hot days when the wind is too gusty to raise the cover. It's all — just like sitting on the ground outside and reclining against the tent's slanting sides — fair use of the tipi.
Once the lining is hung inside and its bottom 6 inches turned in all around, robes, a waterproof tarp, oilcloth, burlap, old linoleum or a plywood floor can be put down inside and lapped over the liner's edge. Waterproof layers are really only needed under the beds and other items affected by dampness.
Ditch around the tipi to lead water away, make a couple of willow rod backrests, hollow out and line a fireplace circle with rocks and you're ready to dedicate your lodge. If you want to make sure the fire draws exceptionally well, you might dig a trench, remove the tops and bottoms from some tin cans and bury them in line to make a vent pipe leading from outside the tipi to the bottom of the fire pit.
So, hang your shield and other medicine articles from a pole behind the altar of your lodge and move in. Forget storm windows, leaky faucets, plugged eave troughs, water in the basement, sticking doors, cracked sinks, missing shingles, compound interest and 40-year mortgages.
Cover and door:
*Other widths of material may be used if you refigure yardage.
It's not hard to roll up a tipi cover and liner for transportation in a station wagon, car trunk, trailer or truck. Seventeen poles — 20 to 25 feet long and weighing a total of approximately 300 pounds — is a little different matter. But don't sweat it: The problem has been faced and solved before.
In the old days, before the Indians obtained horses from the white man, they simply limited their tipis to a size with poles small enough for a dog to drag. During the 1800s, when the tribes had plenty of horses (and a good horse could drag eight to 10 poles), large tipis were transported throughout the Plains. As the buffalo were killed and the prairie fenced in, the Indians turned to wagons. Today, tipi poles are sometimes shipped from one place to another or carried on trucks, campers or cars.
Here's a rack the Laubins rigged up with the help of a Sioux blacksmith friend. With it, they can haul a complete tipi, of the size described in this article, on top of a small coupe.
About 29 feet of 1/2-inch galvanized iron pipe, eight T-joints, two unions and four elbows were used in the basic rack with a 6 foot long 3/8-inch iron rod swung on a flat hinge from each side of the windshield as a brace. The bottom ends of the four uprights simply slide into sockets of 3/4-inch pipe fastened to the inside of the vertical sections on the front and back bumpers.
The only joker is the fact that the Laubins' car happened to be one of those sturdy old gentlemen of 1940ish vintage: You know, the kind with big, rugged, honest bumpers that really stick out in the breeze. If your automobile is one of today's sleek, streamlined monsters with the recessed, tinfoil articles front and rear, you'll obviously have to come up with another system — but the sketch should give you some ideas.
The Laubins load their tipi poles with butt ends forward and sticking over the front rack just a few inches. The long, slender top ends of the poles are allowed to protrude, maybe, 5 or 6 feet. This brings the tail end of the load just over the front of a small trailer they sometimes pull. If you make a rig like this and don't pull a trailer, remember to hang a red flag or two on the tips of the poles.
Cover, liner stakes and all the rest can be bundled up and carried on top of the "raft," if you like. Design your rack so the load just clears the car top and put some kind of a pad between the roof and the poles. Lash everything down securely.
Discover a dazzling array of workshops and lectures designed to get you further down the path to independence and self-reliance.LEARN MORE