Practical Jewelry-Making Techniques: Problem Solving (Firefly Books Ltd, 2012) by Stephen O’Keeffe offers DIY instruction on how beginning jewelry-makers can use simplified methods to create ornate pieces without compromising quality or presentation. Learn how to tie the right knot in order to secure your jewelry creations in this excerpt taken from the book’s chapter entitled, “The Slipknot Necklace”
You can purchase this book from the MOTHER EARTH NEWS store: Practical Jewelry Making Techniques: Problem Solving.
THE SLIPKNOT NECKLACE
Make your selection of beads and thread them onto a length of cord, in this case 1 mm leather. Tie a loose overhand knot on one end of the cord, and pass the other end of the cord through it. Tighten the knot just enough to allow the cord to slip through it to form a noose. Draw the noose to the size which will pass easily over the wearer’s head. Tie the loose end of the cord to the far side of the first knot, using the same overhand knot.
It will now be possible to pull on each knotted end, to shorten the necklace, leaving the knots lying at either side of the neck. A knot tied on each end after the slipknot will prevent the cord from slipping through the fingers.
The slipknot system can, of course, be used back to front, the double section of the cord passing through the pendant so that the slipknots lie out of sight at the back of the neck. In the example pictured at the top of the page both strands have been threaded with beads.
This kind of work can be confusing, so practice first with string; one end of this length has been dyed to make it easier to see how the system works.
As an alternative to the slipknot, a bead with a hole just large enough for two thicknesses of cord can be used as a tightening device. Check the hole in the bead carefully, as any sharp corners can damage the cord. Fine carborundum grit on a piece of string can be used to make the hole smooth.
The figure-of-eight knot, above, (known alternatively as the Savoy knot or the lover’s knot) is used in heraldry as a symbol of faithfulness. To tie this knot, form a loop in the cord, wrap the loose end around the cord below the loop, then pass it through the loop from the top.
An alternative way of combining beads and cord is this design (right) where the beads hang vertically. Choose the beads, and then make a ring in silver just large enough to allow the largest bead to pass through. Tie a loose knot on the end of a one-metre (three-foot) length of cord, thread on the beads, and loosely tie off the other end. Fold the cord double and fasten it to the silver ring at its midpoint using a simple hitch knot. Instead of the silver ring a loop can be made in the cord itself, though this may be too plain and simple.
Each end with its beads can be passed through the ring separately to form the necklace. Once you have decided on the correct length of cord, the knots can be made permanent. As this forms the focal point of the necklace, a basic overhand knot is a bit too plain, so here a blood knot is used.
The blood knot (above) is so-called because it was tied on each of the nine ends of the cat-o’-nine-tails. The blood knot was also used by friars of the strict Capuchin order, as a simple way to add weight to the ends of the rope around their habits. A more mundane name for this knot is the multiple overhand knot.
To make a blood knot, begin with an overhand knot, then continue passing the end of the cord through the loop, three or four times. As it is drawn tight, both ends of the knot must be pulled with the fingers towards the middle, to form neat symmetrical coils. Leave at least 10 mm (1/2 in.) of cord beyond the knot to make it secure, and to show off its symmetry.
Used with permission from Practical Jewelry-making Techniques: Problem Solving by Stephen O’Keefe, published by Firefly Books 2012, $24.95 paperback.