Circular Saw Safety Tips

This useful tool can be used safely if you know what to do (and what to avoid).
By Bob Johnston
April 2, 2009
Add to My MSN

The first thing you do when preparing to cut a board is to make a mark for the cut. About 90 percent of the carpenters I know make a mark with a speed square and cut on the left of the line sometimes and to the right of the line other times. Who knows?The small straight mark on the right is the exact place you want the blade to cut and is the correct way to mark a board, the wing mark on the left of the small mark is the waste side.
BOB JOHNSTON
Slideshow


Content Tools

Related Content

Build Sawhorses: Even Better Than In 1985

Follow the sawhorse plans from our 1985 article (with a few variations), and you can build sturdy, i...

League of American Bicyclists Releases Educational Videos

Instructional videos from the League of American Bicyclists provide basic bicycle safety tips.

Sawing Your Trees Into Lumber, Part 3

How to work with a sawyer when cutting your lumber

Cutting Your Trees Into Your Own Lumber, Part 1

Working with a sawyer to cut custom lumber for your projects can be a great experience. Here are a f...

Last year, more than 250,000 saw-related injuries required emergency room care. The circular saw is the most dangerous, misused and abused tool in a do-it-yourselfer’s tool shed. Here’s what I have learned about safety, proper techniques and maintenance from using a saw for 50 years.

Some History

When portable, electric circular saws were first made, the motor was on the right, the blade on the left and the handle was above the blade. When you got to the end of a cut, the weight of the motor would naturally make the saw fall off to the right and butcher the end of the cut.

Then someone came up with the bright idea of putting the motor on the left and the blade on the right. This shifted the main weight of the saw and the majority of the base to the stable side of the cut. But with the blade on the right, a right-handed person has to lean over the top of the saw to see the line of the cut.

A few years ago, Porter-Cable came out with two models (345 Saw Boss and the 423 Mag) with the blade on the left — and moved the handle so the saw is balanced. Craftsman also has a similar 5 1/2-inch saw. Now some other manufacturers are seeing the light.

If you use your right hand to run a saw, buy one with blade on the left; if you use your left hand, buy one with the blade on the right. You need to see where the blade is cutting to make an accurate cut; and working in a good position is important. The position of making a cut with an electric saw is the same as making a cut with a handsaw or hacksaw: The cut line, the blade, your forearm, elbow and shoulder should all be in one straight line.

Preparing to Cut

Now we come to one of the most overlooked, but most important procedures in using any power tool — plugging in the cord to a ground fault circuit interrupter (GFCI) power cord. (See Image Gallery.)

Keep your finger off the trigger (switch) until you are ready to make a cut. When you plug a saw into a power cord, you have created a power supply for a tool that could easily kill you or maim you for life. If you plug a tool cord in backwards (and it can be done) you have created reverse polarity, and that can kill you.

Never cut a board in the middle that is just lying on two sawhorses, it will sag or collapse about two-thirds of the way through the cut and bind the saw, causing kickback. The only time you can safely cut a board using only two sawhorses and no frame table is when you are only cutting off a short end. Even when using a frame table, make sure the boards don’t bow downward — your saw is likely to bind and kick back.

Never use a circular saw to notch or cut out a stud that is in a framed wall. The saw will buck. Use a reciprocating saw for this procedure.

Always have a safe place to put your saw. Never set it down on the blade guard or drop it on the ground. Always lay a saw on the side the blade is on (not blade up).

Don't stand on the cord. When you run out of cord, the saw could kick back and cut you.

All of the area where you are using a saw should be clean, leaving nothing that could cause you to trip and fall while carrying or using a circular saw.

Adjusting the Saw

Now we are ready to make a cut, but first set the blade depth of the saw blade to the thickness of the board to be cut plus one-eighth inch. (See Image Gallery.)

Place the nose (front) of the saw base on the board to be cut, with the blade about one-quarter-inch from the board, align the blade with the mark as straight as you can, slide your speed square up to the side of the base and grasp it with your hand to secure it to the board. The side of the saw base and the speed square should be exactly parallel.

Make the Cut

Start the motor and slowly push the saw forward until it just touches the board. If you are a little off the mark, back the saw up one-eighth inch (while it is still running) and the vibration of the saw will let you go to the left or right to line up the blade with the mark.

Push the saw slowly through the board and let the saw do its job. Do not crowd the saw (push it too fast). You will feel when the saw has cut through the board, because they will both move, only slightly, but you will see and feel them separate.

Now, take your finger off the trigger and do not move the saw. Let the motor and blade come to a complete stop. Never lift or move a saw from a cut while it is still running. This is the most important thing to remember.

Now, for those of you who have never or rarely used a circular saw and are now afraid of even picking one up, let me say that a circular saw is a safe tool — if used properly. For your first few hundred cuts, I suggest not using a speed square as a guide. Make your mark, draw a line on the board and make the cut. It takes a little longer, but it will build your confidence.

Maintenance and Other Tips

Never depend on a blade guard to protect you. Blade guards are notorious for hanging up and not going back down, especially when you drop the saw on the guard a few times. Keep the guard well lubricated and keep the housing clean of pitch and sawdust.

Check all of the screws and bolts on your saw to make sure they are tight.

If you are cutting a board and the motor slows down, you are either crowding the saw (pushing too hard), cutting on a bowed down table, have a dull blade or the lumber is pinching. If your saw slows down and starts binding, stop the motor and pry the blade out of the cut. Try to cut it from the other side or throw the board away.

Be careful, making one mistake with a circular saw could be the last thing you ever do in your life. But when used correctly, a circular saw is a wonderful tool for increasing efficiency in your building projects.

Bob Johnston, of Cloudcroft, N.M., has been a carpenter for over 50 years.


You might also be interested in reading Choose Rechargeable Tools for Safety and Versatility and You Can Build Sawhorses.


Previous | 1 | 2 | 3 | Next






Post a comment below.

 

steve_67
3/16/2011 3:40:28 AM
I have a problem with them changing the side of the saw the blade is on. When you are end cutting a board you can not hold the board still. If you cut on the otherside, the saw rest won't be on the board. I almost lost 4 of my fingers 2 years ago. I was cuttig the end of a board with a cordless saw. I had the saw rest on the wood so now the blade is at the end of the board in my right hand. I started the cut, the board started to move. I reached with my left hand to hold the board, Right into the blade. If this was a saw with the blade on the right I would have been cutting on the otherside of the wood and the board would be able to hold with my left hand. The sewed my fingers back on but I have permanent nerve damage. I have been using circular saws for 30+ years and that was the first time I have had an accident. I swear to never use a saw like that again and I will tell everyone else the same!

TexasJack
4/22/2010 2:58:36 PM
As a journeyman carpenter, I worked 10 years as carpenter foreman for the Texas prison system (as employee, not inmate) where I learned quickly a convict can make anything out of nothing 'n usually successfully hide it but for intelligence, they usually put selves and others at safety risk without lot of effort, which brings up a safety issue often overlooked by amateurs, laymen, and incarcerated felons -- never, ever use an inverted circular saw with blade guard restricted 'n mounted underneath a plywood base as a makeshift tablesaw. Not only is it unsafe without the guard, it's a surefire way to cutoff fingers, a fate an inmate accomplished, by accident, while working for one of my employee supervisors. If there is anything worthwhile about his incidental negligence, it's this: he won't be picking anymore locks in the free world when he makes parole.

Teddy Deane
4/9/2009 10:07:05 PM
As an additional safety tip for circular saws, I'm always aware of my cord placement. Sometimes the saw will just seem hard to move when cutting a panel only to find out that the cord is caught up somewhere. If you don't realize this you start pushing harder and this is obviously very dangerous, especially if the cord suddenly lets go..

oliver_3
4/9/2009 3:58:57 PM
having spent the last 3 months in surgery and rehab after nearly cutting my thumb with one, I am now kind of ok: thanks to modern micro surgery My ONE extra advice: ALWAYS hold your saw with TWO hands... kickback with 2 hands is manageable(maybe),it is not with one. and not sure yet when I will be confident enought to start using one again!!!!

Jim Wurzbach
4/9/2009 1:19:56 PM
And always keep your hands where you can see them or your fingers may end up on the floor.

Keith Hallam_1
4/8/2009 9:47:02 AM
Hi, any adjustments to the circular saw, or any power tool for that matter, should be done with the power cable unplugged from the wall. This wasn't made clear when adjusting the depth of the cut.








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.