Build a Hot Tub!

Here's the story of how a not especially handy couple successfully followed through on their decision to build a hot tub.
By Joan and George Campbell
March/April 1980

The authors and a friend enjoy a soak in their finished tub.
PHOTO: JOAN AND GEORGE CAMPBELL
Slideshow


Content Tools

Related Content

How to Try and Grow a Giant Pumpkin

Whatever you do in your garden or flower beds, the most important thing is to have fun taking care o...

Hot Tubs and Motorcycles

How a wood-fired hot tub allows us to live better on less energy.

Fairmont Hotels: The Ultimate Green Luxury

Natural Home editor-in-chief Robyn Griggs Lawrence reviews the sustainably minded Fairmont Hotels.

The Home Know-It-All

Check out this blog for great information on do-it-yourself projects and more!

When our neighbor set up an elaborate steel tank, water pump, and heater complex in his back yard, my wife Joan and I wondered if the poor fellow was losing his marbles. And—when he then filled the giant bath apparatus with 110°F water . . . and asked us to join him in a dip—we knew he was crazy. Somehow, though, we finally agreed to shed our clothes and slowly (verrrry slowly) lowered our bodies into the steaming pool. The heated liquid made our hearts race and our limbs turn into limp rubber bands but—amazingly enough—felt delicious!

After a few blissful minutes, Joan and I both felt the urge to cool off, so we languidly dragged ourselves out of the tub. The night air felt unusually warm . . . then a wee bit crisp . . . and soon so downright cold that we were eager to plunge right back into the steaming vat and begin the cycle all over again.

In other words, we had both become as "crazy" as our neighbor ... we'd been stricken with the divine madness of hot tub bathing.

The human pastime of soaking—or steaming—oneself in sweltry water has a long and respectable pedigree. The Finns have a tradition of drenching themselves in hot saunas (and then rolling in the snow!), while the Japanese bathe in ofuros warmed to as high as a scalding 120°F ... and health-seeking people of all nationalities and classes have—for eons—lowered themselves into natural hot springs. Now, more and more Americans have choosen to build a hot tub and share the relaxing joys of soaking. Many of these hot tub enthusiasts will tell you the experience is good for the circulation, for inducing a sleep that rivals the untroubled slumbers of childhood, for bringing body and soul together, and for providing a sense of warmth and community with others. But—even though everything these zealots say is true —we think the real reason folks sit in heated vats is simply because it's pure, unadulterated fun.

Bathing Bliss for $250

As you may have guessed by now, we Campbells were so infected by hot tub madness that we became determined to have a "poaching pool" of our own. We soon discovered, though, that we'd have to build—not buy—our bath of bliss ... because most commercial hot tubs cost well over $1,000. (We wanted to soak, but not get soaked!) Once we'd reached that conclusion, we had to decide what material to use for our hot tub's vat and figure out a way to warm the bath water. Neither Joan nor I can claim to be much of a "handyperson" when it comes to carpentry or welding, so homemade wood or steel tubs were out of the question. We needed a material that could hold a ton of heated H20, yet one that amateur do-it-yourselfers could work with. We settled on concrete.

Our next question was what energy source to use for the hefty task of heating our planned tub's 250 gallons of water from 60° to 110°F. Most hot tubs are fired by natural gas, but we opted for a renewable fuel: wood.

Once we'd made those two choices, all the job required was careful planning, a bit of down-home cobbling, and a considerable amount of plain old-fashioned work. And, when it was all done, we'd constructed our own limb- and soul-soothing hot tub . . . for only $250!

Here's how we did it.

The Foundation Trilogy: Forms, Steel, and Concrete

Our first task was to build a cement base that would be sturdy enough to support both our square, concrete-block tub and lots of water. We picked a level, private, wind-shielded site, dug a 6-foot-square by 6-inch-deep pit ... and lined this foundation hole with a wooden form made from scrounged 2" x 6" lumber. Then we dug out four additional channels (6 inches deeper than the rest of the excavation) following the lines that would later mark the four sides of the tub. (The trenches allowed us to provide a doublethick concrete base—for extra support—under the tub's walls.)

Next we installed a grid of 16" squares—made from eight lengths of 3/8" steel reinforcing bar—to strengthen the foundation, and then put our inlet and outlet pipes in place. Each of the conduits was fitted with a flange (set on a 3" nipple) in its "in tub" end and a 6" nipple at its far end . . . to raise the pipes' tips above the level of the to-be-poured concrete. We also marked the location of the rebar pieces on the wooden forms (so we'd know where they were, later) and covered the pipe ends with tape to keep the openings clean.

The time had come to add concrete. We bought ours ready-mixed and poured in 3/4 of a yard, positioned the pipe openings and rebar grid with our hands, and leveled the concrete's surface with a long 2 X 4. Then we sank six U-shaped 12" x 16" x 12" pieces of reinforcing steel—bases down—six inches into the wet cement. These rebar "horseshoes" were (using the guidance provided by our previous frame markings) lined up at the outside intersection points of our grid ... so their "up" ends would poke into the concrete blocks. Joan and I sprayed our new "floor" frequently during the following two days (to let the base cure properly) and then began our masonry work.

Concrete Blocks Are All They're Stacked Up to Be

Somehow I ended up with the job of laying the four levels of blocks for the sides of our tub. I started this chore by lining up string boundaries for the first layer of block placements. (The bricklaying pattern was three blocks set "longways" and one "endways" on every wall ... which meant the rebar horseshoe uprights would go through every other block hole on each side.)

I cured the first layer (spraying it periodically) for two days before adding the other three levels. Then I thrust lengths of rebar into the block holes that were already supported—from their bottoms—by the "horseshoe" ends, filled all the openings with concrete ... and capped the wall with a layer of 8" x 16" stepping stones.

Now I'm a "fur piece" from being a master mason, so Joan and I were a bit nervous about the possibility of leaks. And sure enough—when the tub had finished its two weeks of curing—the dang thing spewed water from so many joints we could hardly fill it! The damage was reparable, though. We just added successive layers of a waterproof patching compound, a building block coating, and an airtight water seal . . . until we'd produced a tub so leakproof it was seaworthy!

Our Heat Feat

Of course, we still had to figure out how to heat all that bath liquid. As you know, we'd planned to use wood heat to "bile up" our hot tub, but constructing such a system turned out to be harder in the doin' than it was in the imaginin'.

We first tried to adapt our home's Franklin stove to the purpose. I used a spring-type tubing bender to coil 50 feet of 1/2" copper tubing into an 8" diameter spiral (leaving five feet of straight pipe on each end) and gingerly stuffed this copper "spring" into the wood-burner's chimney. I then constructed a plumber's nightmare of pipework to hook this coil up to our small garden fountain pump and to the water-filled tub. Once the contraption was all set up, we lit the Franklin, crossed our fingers, and hoped for the best.

Eighteen hours later, half our wood pile had gone up in smoke and the house felt like the inside of a Dutch oven . . . but the water still wasn't hot enough to soak in properly! Down came the coil, the pipework, and our hopes . . . until I spotted an ad (in a back issue of MOTHER EARTH NEWS) for a conversion kit to change an old oil drum into a wood stove. That enticement inspired me to construct my own 55-gallon barrel stove.

A welder friend fabricated a stove door (complete with draft opening) out of 3/16" steel plate, while I used a saber saw to carve the loading hole in the barrel itself. I then secured the door in place with galvanized T hinges.

Moving to the back end of the stove, I cut a 7"-diameter "smokestack" hole in the barrel's side and attached the chimney itself by cutting—and bending to 90° angles—a series of 2" tabs around the bottom pipe section . . . and fastening this "collar" to the drum with sheet metal screws. I also snipped slots in the upper part of the stovepipe (to accommodate the "in" and "out" copper coil lines) and installed a damper above the water-heating spiral. Last of all, I made four spraddled legs to support the heater . . . using flanges, backing plates, and two-foot sections of 1/2" galvanized pipe.

After placing the finished stove a safe distance from our house, I fastened the free ends of the copper coil tubing to some CPVC conduit (with compression fittings, galvanized unions, and two short pieces of galvanized pipe) and ran the outlet line through a hose fitting and into the tub. The intake line was equipped with a valve, hooked to the pump, and then plumbed up to the vat. (The pump was "tied in" to the line with female fittings and short pieces of hose ... so that it could be disconnected if necessary.)

We were ready to start cooking. I put a layer of sand in the drum, loaded the cylinder up with scrap lumber, flushed water through the system with a garden hose until all the air was out of the pipe complex, plugged the drain end ... and fired 'er up. Once the stove got going, I adjusted the flow of water from the hose through the heating coil to around 40 gallons per hour . . . so that the temperature of the liquid as it left the heater was about 130°F.

When the tub was full (by that time the water had cooled to 110°), I disconnected the hose and started up the pump. We quickly found that our stove fire had to be kept small or the water in the coils would "boil out" ... causing an air lock that would stop our little pump. (A larger "circulator" should avert this difficulty.)

Rub-A-Dub-Dub, We Built a Hot Tub

Well, we'd finally done it: The two of us had constructed a strong, watertight hot tub that could be easily brought up to—and maintained at—the proper temperature. Our work was over.

The whole job seemed to have taken forever. But when night fell and we eased ourselves slowly into the mind- and muscle-soothing water (with a candle casting a golden light upon the scene), we knew the project had been worth all the effort.


Hot Tips

Here are a few extra bits of tub lore to help you on your restful way:

PLASTIC PIPE: We used CPVC pipe. Regular PVC can't take the heat.  

SEATING: Concrete blocks topped with stepping stones allow adjustable seating in our comfortable four person tub.

COVERING: A 4' x 4' square of plywood with handles and backing makes a nice roof to hold heat in while keeping leaves and/or critters out. Styrofoam insulation — added to the underside of this covering — would provide even better heat retention when the tub is not in use.

CHLORINE: A cup of bleach per bath keeps the germs down. (The chemical's unpleasant odor can be masked with lemons, mint sprigs, jasmine blossoms, or various oils and essences.)

FILTERS: Water filters will keep you from having to drain the tub after every three or four uses, as we do . . . but they are, of course, an additional expense. We simply installed a hose cock on our drain line so the "tired" bathing liquid can be used to water the garden.  

SAFETY: Make sure your pump is well grounded, don't drink too much alcohol while "tubbing," don't let the water get too hot, and don't stay in your tub for too long at one time. In other words, use plain ol' common sense, and remember that you're sitting in a vat of very hot water.

TEMPERATURES: Most tubs are kept at temperatures ranging from a tepid 100° to a sizzling 115°F (a dial- type photographer's darkroom thermometer is handy for taking comfort readings). We've found the best temperature for social soaks to be be tween 105° and 107°, while 110° to 115° will penetrate clear to the bone.  

REFERENCES: Leon Elder's Hot Tubs (Random House) is a fine introductory volume, while Build Your Own Hot Tub (Ten Speed Press) by Ed Miller and Steven Flamm tells how to construct a wooden, conventionally heated vat for $500.


Previous | 1 | 2 | 3 | 4 | 5 | Next






Post a comment below.

 

rainie.flores.7
5/13/2013 1:57:09 AM

How do we get started in building a hot tub? Isn't it time consuming plus, i'm not sure if my husband is skillful enough to build our own hot tub. I think i might as well purchase a hot tub. There are hot tubs available in the market that are easy on the budget.

- http://www.southeastspas.com/


Phyllis Mathison
1/22/2012 8:42:05 PM
Hello ....I took an old water tank that holds about 150 gallons .....It had steel legs so I didn't have to weld any on. Cut the top off added hinges to the side of the tank and put the part I cut off back on to use it as a lid to keep the water hot as I fill it.. put wood under a part of the tank and it heats up in about a hour.To empty the water drill a hole in the bottom and use a ear plug to block the hole or drill a bigger hole and just use a sink plug....I have had many relaxing days in my hot tub and also invited a friend over too .Mine fits 2 comfortably.

Art Glick
7/30/2010 12:21:05 AM
Greater caution should be urged with respect to maximum temperature. It can be downright dangerous to bathe in water hotter than 104 F unless you've painstakingly acclimated yourself to such temperatures. Pregnant women, especially in the earliest part of their term, should not bathe in water hotter than 100 F. The main item missing from this design is hydrotherapy. Steeping in hot water is one thing, but add in some good powerful jets and it really is almost like heaven. Your sore muscles will love you for it. The need for chlorine can be totally eliminated through the use of a metal ionizer (e.g. copper/silver/zinc). Ozonaters are as harmful as the halogens. Your health, your equipment and the environment will appreciate this. A fellow named Paul Maunders who lives in the U.K. built a similar vessel and described each step of the project in even greater detail (complete with pictures)... http://www.buildatub.co.uk/

morgan_5
3/26/2009 2:14:29 PM
This sounds pretty cool, but do you really use bleach, and then use that water to water your garden?

Mark_5
11/28/2008 6:09:14 AM
I am finishing up a wood fired ...plywood hottub this weekend . I have worked on this thing since July 4 and just now working out all the kinks. but its awesome.

jay peck
11/12/2008 3:18:44 PM
Need Plans to build wooden hot tub. Anything additional that you can think of on this idea. jay

Rod_6
1/20/2008 1:45:49 PM
Hi Does anyone have plans to build a hottub from a very large barrel, with details of how to heat the water too. I would appreciate any help. Cheers Rod

mary_72
11/29/2007 9:13:30 AM
Sounds great. We live in Turkey and have an old water heater placed outside our bathroom which we light on the darker days when the solar water heater isnt hot enough. We now intend to use this when we build a hot tub like yours. Looking forward to that first dip! thanks so much for the info.








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.