Build a Homemade Mousetrap

Build a homemade mousetrap to safely nab a mouse, as our two simple (and humane) traps prove, including the wooden cell mousetrap and can mousetrap, and mousetrap diagrams and construction directions.

| November/December 1982


Homemade mousetraps: A wooden mousetrap.


Use these instructions to build two different homemade mousetraps. One design resembles a wooden cell and the other uses a recycled soup-can. A diagram for the soup-can mousetrap can be found in the image gallery (above).

Wooden Cell Mousetrap

This "Old World" model is based on a Danish design and — although it fairly screams "Rube Goldberg" — it's functional (and even sort of fascinating).

To make it, you'll need an all-wire coat hanger, a strip of pine measuring 1/4 inches by 2-1/2 inches by 54 inches, another scrap of softwood with 3/4 inch by 1-1/4 inch by 4 inch dimensions, about two dozen 16-gauge, 5/8 inch wire brads and a 3-penny finishing nail. The only tools required are a coping saw, a ruler, a hammer, a nail set, a pair of wire cutters, and a drill with an assortment of bits.

Begin by cutting up your 1/4 inch plank to produce the pieces called for in the illustration. Once you've done so, use a No. 48 bit to drill lines of holes — keeping the individual bores about 5/16 inches apart—with each series parallel to and 1/4 inch from one of the short ends of the 1/4 inch by 2-1/2 inch by 9-1/4 inch and the 1/4 inch by 1-1/2 inch by 2-1/8 inch by 5 inch panels — and drill yet another hole through each of the latter parts, at a point 1 inch from the straight edge and 3-1/4 inches from the wide end. (To keep the openings lined up, it's best to clamp the matching pairs of pieces together, then bore the necessary holes. Note, also, that the lines of openings in the ends of the two wedge-shaped panels don't extend all the way across the pieces, but terminate 1-1/4 inches down from the peaked corners.)

Next, clip apart your coat hanger to form bars of two different lengths. (You'll need six that are 1-7/8 inches long and seven that are 2-3/4 inches long.) With this done, tack the box together using some wire brads (make sure its walls are positioned between the top and bottom boards, and that the bar holes in the upper and lower panels are at the same end of the box), then tap the seven hanger rods into place. Complete the cage by drilling a 1/8 inch hole through the bottom board, being certain it's centered and 3/4 inches from the end opposite the bars.

To assemble the ramp mechanism, first tack the narrow ends of the wedge-shaped pieces to the sides of the softwood block (the lower edges of the 1/4 inch walls should be flush with the bottom of the 3/4 inch by 1-1/4  inch by 4 inch plug, and the joint should be 1-3/4 inches long), then tap five more bars into the aligned openings. Also, make a security pin by cutting a 3/4 inch piece from the finishing nail and driving it into the bottom of the softwood block at a point 1 inch from its inside edge.

anabell jones
11/27/2013 11:28:25 AM

Don't waste your time on the soupcan trap. It *doesn't* work. No doubt, it can, probably, catch some tiny percentage of mice. But, over all, it doesn't work because it's a design error. I could see from the beginning that it seemed flawed, but, I built it anyway because I'm waiting for some snap traps. All I've been doing is giving the little vermin free meals. As someone who has caught many rodents in snap traps (both, mice and rats), and have seen how frequently they make off with the bait a lot of the time, I can see what the problem, here, is. But, because whoever contributed this "gizmo" is probably picking people's brains in order to get us to tell *him* how to make it work, I refuse to state what it is. Even the picture, accompanying the skimpy instructions, looks like it was filched from somewhere. I doubt that the person actually tried it. I do like the way that it closes, and would like to see how well it would hold a trapped mouse. The problem is that part of the design needs to be improved. There is a reason as to why snap traps have stood the test of time. Snap traps are, probably, the best simple-machine blend of form and function for catching these destructive little thieves. And, they are reusable, too. Useless ideas, like this one, belong in a Tom and Jerry cartoon.

jane fenters
11/1/2012 12:31:50 PM

DO NOT release living mice and rats back into the world. They are vermin, carry disease, eat tons of valuable food each year and reproduce like crazy.

don nell
10/31/2012 10:00:22 PM

Hey Bob and Mike...Go to the top of page two and click on "Image Gallery" click on the second page there and you will see the can trap. Go to the next page and there is an excellent diagram of the trap. Just thought I would help you out.

bob currey
10/31/2012 8:11:25 PM

They posted links to this all over the web to get people to come to look at this article. It occur to me that they are making money based on the number of hits to the page from all the ads on the page, and the actual usefulness of the page itself might not be as important as just getting people to click to here. It looks like its from an article from Nov 82, and whoever transcribed it over to the web left out the referenced illustrations. I guess if we want to know we have to dig thru our back issue boxes to find it, or buy the CD set. I tried googling for it, but all I found were a bunch of websites that ALL linked back to here.

michael conlin
10/31/2012 7:54:11 PM

If they're going to give you this much info, why hld back on the pics?

bob currey
10/31/2012 5:22:59 PM

They left out the illustrations. I wonder how it works?

10/31/2012 2:34:55 PM

"Humane" implies that I remember to let the little guy out before he dehydrates. (Guilt) (Guilt) (Guilt)

12/5/2007 11:57:00 AM

I did build a mousetrap about 25 years ago for my mother thats why I call it mothers mouse trap, it is made of card board and disposible, if you would like i will be happy to send you a picture of it... thanks Ron

dairy goat


Aug. 5-6, 2017
Albany, Ore.

Discover a dazzling array of workshops and lectures designed to get you further down the path to independence and self-reliance.