Repurpose Vise Grips By Making a Bicycle Stand

Put old Vise Grips to new use by making a bicycle stand, including directions, tips and a diagram.
By the MOTHER EARTH NEWS editors
May/June 1982
Add to My MSN

Create your own bicycle stand with a pair of worn-out Vise grips.
PHOTO: MOTHER EARTH NEWS STAFF
Slideshow


Content Tools

Related Content

Multidirectional Ratchet Bar Clamp

You can repurpose broken tools to make this easy-to-assemble multidirectional ratchet bar clamp syst...

Village Bicycle Project Benefits Poor African Families

Peckham’s Village Bicycle Project donates used bicycles and parts to poor families in Africa, and th...

Nifty Tote Bag Made From a Feed Bag

Easy-sew step-by-step instructions (with photos) to repurpose feed bags into handy totes.

Enter the Stromer Electric Bike Contest for a Chance to Win a New E-Bicycle

Swiss manufacturer Stromer has announced a sweepstakes to give away a new electric bicycle in the U....


How to Make a Bicycle Stand

Start by shaping and assembling the conduit frame. We've found that a 64-inch length of E.M.T., bent at a 60-degree angle in the center to create two 24-inch legs, works well for a base . . . and that a 46-inch piece, curved to 80 degrees at one end, will provide a suitable upright. Before brazing the vertical arm to the leg tube, though, do shape the end of the pole — using your saw and file — so it matches the contour of the base tubing (you won't be able to produce a secure joint without first performing this step).

The upright can be either positioned vertically or canted inward (5 degrees or so) to provide for additional clearance. And if you plan to work on bikes in the 40-pound (and up) range, you might consider fastening a pair of 12-inch struts between the stanchion and the tubular base for extra support.

To adapt the Vise Grips for cycle-biting duty, first cut two 4-inch lengths of 1/8-by-1-by-1-inch angle iron, then trim away the ends of the tool's "mandibles" so the pair of angles will fit flush against the closed jaws when the adjusting nut is drawn in. Make sure the angles form a square with each other and that the pliers are centered on, and perpendicular to, the irons. Then braze each one securely to its respective mount.

The clamp mechanism is unique not only because it incorporates Vise Grips, but also because it features an all-position swivel. To give the stand this capability, just file or grind a section of 3/4-by-2-1/2-inch pipe until it slips easily into the open end of the upright stanchion, and braze a 1/2-inch nut inside this hollow plug in such a way that its outer face is flush with one end of the pipe (you may have to file the nut's corners slightly if it's to fit properly). Then sink the plug's opposite end 5/8 inch into the curved E.M.T. support and braze it in place.

Next, cut a 2-inch length of conduit from your scrap, and braze a 1/2-by-1-1/4-inch bolt to its side, off center. Then fasten a 1/2-inch nut to the upper jaw of the Vise Grips, right over the rivet, in the same manner. By spinning a third 1/2-inch nut onto the exposed bolt and threading the clamp assembly onto the end of that stud, you can use the free nut to lock the grip in any position. Then, to complete the swivel, just slip the clamp's collar over its pipe plug (with the flank bolt closest to the end) and run a 1/2-by-1-1/2-inch bolt, with a washer, into that stem's countersunk nut to serve as a lock.

Wrap the project up by giving the stand a coat or two of your favorite paint and gluing some 2-by-4-inch leather pads to the inside surfaces of the new angle jaws to prevent damage to the bike's finish. (You might also want to slip some rubber caps over the legs' sharp ends for safety's sake.) Since the modified Vise Grips are still fully adjustable — and likely almost as tenacious as they were when you bought them — you may find that your creation will serve other purposes in addition to grabbing bicycles. In fact, the homemade stand is so useful that you might just want to purchase a new pair of Vise Grips and use your present one in this project... even if it's not worn out yet!








Post a comment below.

 








Subscribe Today - Pay Now & Save 66% Off the Cover Price

First Name: *
Last Name: *
Address: *
City: *
State/Province: *
Zip/Postal Code:*
Country:
Email:*
(* indicates a required item)
Canadian subs: 1 year, (includes postage & GST). Foreign subs: 1 year, . U.S. funds.
Canadian Subscribers - Click Here
Non US and Canadian Subscribers - Click Here

Lighten the Strain on the Earth and Your Budget

MOTHER EARTH NEWS is the guide to living — as one reader stated — “with little money and abundant happiness.” Every issue is an invaluable guide to leading a more sustainable life, covering ideas from fighting rising energy costs and protecting the environment to avoiding unnecessary spending on processed food. You’ll find tips for slashing heating bills; growing fresh, natural produce at home; and more. MOTHER EARTH NEWS helps you cut costs without sacrificing modern luxuries.

At MOTHER EARTH NEWS, we are dedicated to conserving our planet’s natural resources while helping you conserve your financial resources. That’s why we want you to save money and trees by subscribing through our earth-friendly automatic renewal savings plan. By paying with a credit card, you save an additional $5 and get 6 issues of MOTHER EARTH NEWS for only $12.00 (USA only).

You may also use the Bill Me option and pay $17.00 for 6 issues.